Center for Quantum Devices - Most Downloaded Journal Articles

Page 5 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)

17.	High-speed free-space optical communications based on quantum cascade lasers and type-II superlattice detectors Stephen M. Johnson; Emily Dial; M. Razeghi Proc. SPIE 11288, Quantum Sensing and Nano Electronics and Photonics XVII, 1128814-- January 31, 2020 ...[Visit Journal] Free-space optical communications (FSOC) is a promising avenue for point-to-point, high-bandwidth, and high-security communication links. It has the potential to solve the “last mile” problem modern communication systems face, allowing for high-speed communication links without the expensive and expansive infrastructure required by fiber optic and wireless technologies 1 . Although commercial FSOC systems currently exist, due to their operation in the near infrared and short infrared ranges, they are necessarily limited by atmospheric absorption and scattering losses 2 . Mid-infrared (MWIR) wavelengths are desirable for free space communications systems because they have lower atmospheric scattering losses compared to near-infrared communication links. This leads to increased range and link uptimes. Since this portion of the EM spectrum is unlicensed, link establishment can be implemented quickly. Quantum cascade lasers (QCL) are ideal FSOC transmitters because their emission wavelength is adjustable to MWIR 3 . Compared to the typical VCSEL and laser diodes used in commercial NIR and SWIR FSOC systems, however, they require increased threshold and modulation currents 4 . Receivers based on type-II superlattice (T2SL) detectors are desired in FSOC for their low dark current, high temperature operation, and band gap tunable to MWIR 5. In this paper, we demonstrate the implementation of a high-speed FSOC system using a QCL and a T2SL detector. [reprint (PDF)]
17.	Optical Coatings by ion-beam sputtering deposition for long-wave infrared quantum cascade lasers J. Nguyen, J.S. Yu, A. Evans, S. Slivken and M. Razeghi Applied Physics Letters, 89 (11)-- September 11, 2006 ...[Visit Journal] The authors report on the development of high-reflection and multilayer antireflection coatings using ion-beam sputtering deposition for long-wave infrared (λ~9.4 μm) quantum cascade lasers. A metallic high-reflection coating structure using Y₂O₃ and Au is demonstrated to achieve a high reflectance of 96.70%, and the use of a multilayer anti-reflection coating structure using PbTe and ZnO is demonstrated to achieve a very low reflectance of 1.64%. [reprint (PDF)]
17.	High-performance bias-selectable dual-band mid-/long-wavelength infrared photodetectors and focal plane arrays based on InAs/GaSb Type-II superlattices M. Razeghi; A. Haddadi; A.M. Hoang; G. Chen; S. Ramezani-Darvish; P. Bijjam Proc. SPIE 8704, Infrared Technology and Applications XXXIX, 87040S (June 11, 2013)-- June 11, 2013 ...[Visit Journal] We report a bias selectable dual-band mid-wave infrared (MWIR) and long-wave infrared (LWIR) co-located detector with 3 μm active region thickness per channel that is highly selective and can perform under high operating temperatures for the MWIR band. Under back-side illumination, a temperature evolution study of the MWIR detector's electro-optical performance found the 300 K background-limit with 2π field-of-view to be achieved below operating temperatures of 160 K, at which the temperature's 50% cutoff wavelength was 5.2 μm. The measured current reached the system limit of 0.1 pA at 110 K for 30 μm pixel-sized diodes. At 77 K, where the LWIR channel operated with a 50% cutoff wavelength at 11.2 μm, an LWIR selectivity of ∼17% was achieved in the MWIR wave band between 3 and 4.7 μm, making the detector highly selective. [reprint (PDF)]
17.	Multi-band SWIR-MWIR-LWIR Type-II superlattice based infrared photodetector Manijeh Razeghi, Arash Dehzangi, Jiakai Li Results in Optics Volume 2, January 2021, 100054 https://doi.org/10.1016/j.rio.2021.100054 ...[Visit Journal] Type-II InAs/GaSb superlattices (T2SLs) has drawn a lot of attention since it was introduced in 1970, especially for infrared detection as a system of multi-interacting quantum wells. In recent years, T2SL material system has experienced incredible improvements in material quality, device structure designs and device fabrication process, which elevated the performances of T2SL-based photo-detectors to a comparable level to the state-of-the-art material systems for infrared detection such as Mercury Cadmium Telluride (MCT). As a pioneer in the field, center for quantum devices (CQD) has been involved in growth, design, characterization, and introduction of T2SL material system for infrared photodetection. In this review paper, we will present the latest development of bias-selectable multi-band infrared photodetectors at the CQD, based on InAs/GaSb/AlSb and InAs/InAs1-xSbx type-II superlattice. [reprint (PDF)]
17.	Recent progress of quantum cascade laser research from 3 to 12 μm at the Center for Quantum Devices MANIJEH RAZEGHI,* WENJIA ZHOU,STEVEN SLIVKEN,QUAN-YONG LU,DONGHAI WU, AND RYAN MCCLINTOC Applied Optics Vol. 56, No. 31 -- October 10, 2017 ...[Visit Journal] The quantum cascade laser (QCL) is becoming the leading laser source in the mid-infrared (mid-IR) range, which contains two atmospheric transmission windows and many molecular fingerprint absorption features. Since its first demonstration in 1994, the QCL has undergone tremendous development in terms of the output power, wall plug efficiency, wavelength coverage, tunability and beam quality. At the Center for Quantum Devices, we have demonstrated high-power continuous wave operation of QCLs covering a wide wavelength range from 3 to 12 μm, with power output up to 5.1 W at room temperature. Recent research has resulted in power scaling in pulsed mode with up to 203 W output, electrically tunable QCLs based on monolithic sampled grating design, heterogeneous QCLs with a broad spectral gain, broadly tunable on-chip beam-combined QCLs, QCL-based mid-IR frequency combs, and fundamental mode surface emitting quantum cascade ring lasers. The developed QCLs will be the basis for a number of next-generation spectroscopy and sensing systems. [reprint (PDF)]
17.	Extended short-wavelength infrared nBn photodetectors based on type-II InAs/AlSb/GaSb superlattices with an AlAsSb/GaSb superlattice barrier A. Haddadi, R. Chevallier, A. Dehzangi, and M. Razeghi Applied Physics Letters 110, 101104-- March 8, 2017 ...[Visit Journal] Extended short-wavelength infrared nBn photodetectors based on type-II InAs/AlSb/GaSb superlattices on GaSb substrate have been demonstrated. An AlAsSb/GaSb H-structure superlattice design was used as the large-bandgap electron-barrier in these photodetectors. The photodetector is designed to have a 100% cut-off wavelength of ∼2.8 μm at 300 K. The photodetector exhibited a room-temperature (300 K) peak responsivity of 0.65 A/W at 1.9 μm, corresponding to a quantum efficiency of 41% at zero bias under front-side illumination, without any anti-reflection coating. With an R × A of 78 Ω·cm² and a dark current density of 8 × 10⁻³ A/cm² under −400 mV applied bias at 300 K, the nBn photodetector exhibited a specific detectivity of 1.51 × 10¹⁰ Jones. At 150 K, the photodetector exhibited a dark current density of 9.5 × 10⁻⁹ A/cm² and a quantum efficiency of 50%, resulting in a detectivity of 1.12 × 10¹³ Jones. [reprint (PDF)]
17.	Avalanche multiplication in AlGaN based solar-blind photodetectors R. McClintock, A. Yasan, K. Minder, P. Kung, and M. Razeghi Applied Physics Letters, 87 (24)-- December 12, 2005 ...[Visit Journal] Avalanche multiplication has been observed in solar-blind AlGaN-based p-i-n photodiodes. Upon ultraviolet illumination, the optical gain shows a soft breakdown starting at relatively low electric fields, eventually saturating without showing a Geiger mode breakdown. The devices achieve a maximum optical gain of 700 at a reverse bias of 60 V. By modeling the device, it is found that this corresponds to an electric-field strength of 1.7 MV/cm. [reprint (PDF)]
17.	Bias–selectable nBn dual–band long–/very long–wavelength infrared photodetectors based on InAs/InAsSb/AlAsSb type–II superlattices Abbas Haddadi, Arash Dehzangi, Romain Chevallier, Sourav Adhikary, & Manijeh Razeghi Nature Scientific Reports 7, Article number: 3379-- June 13, 2017 ...[Visit Journal] Type–II superlattices (T2SLs) are a class of artificial semiconductors that have demonstrated themselves as a viable candidate to compete with the state–of–the–art mercury–cadmium–telluride material system in the field of infrared detection and imaging. Within type–II superlattices, InAs/InAs_1−xSb_x T2SLs have been shown to have a significantly longer minority carrier lifetime. However, demonstration of high–performance dual–band photodetectors based on InAs/InAs_1−xSb_x T2SLs in the long and very long wavelength infrared (LWIR & VLWIR) regimes remains challenging. We report the demonstration of high–performance bias–selectable dual–band long–wavelength infrared photodetectors based on new InAs/InAsSb/AlAsSb type–II superlattice design. Our design uses two different bandgap absorption regions separated by an electron barrier that blocks the transport of majority carriers to reduce the dark current density of the device. As the applied bias is varied, the device exhibits well–defined cut–off wavelengths of either ∼8.7 or ∼12.5 μm at 77 K. This bias–selectable dual–band photodetector is compact, with no moving parts, and will open new opportunities for multi–spectral LWIR and VLWIR imaging and detection. [reprint (PDF)]
17.	Thermal stability of GaN thin films grown on (0001) Al₂O₃, (0112) Al₂O₃ and (0001)Si 6H-SiC substrates C.J. Sun, P. Kung, A. Saxler, H. Ohsato, E. Bigan, M. Razeghi, and D.K. Gaskill Journal of Applied Physics 76 (1)-- July 1, 1994 ...[Visit Journal] Single crystals of GaN were grown on (0001), (0112) Al₂O₃ and (0001)Si 6H‐SiC substrates using an atmospheric pressure metalorganic chemical‐vapor‐deposition reactor. The relationship has been studied between the thermal stability of the GaN films and the substrate’s surface polarity. It appeared that the N‐terminated (0001) GaN surface grown on (0001)Si 6H‐SiC has the most stable surface, followed by the nonpolar (1120) GaN surface grown on (0112) Al₂O₃, while the Ga‐terminated (0001) GaN surface grown on (0001) Al₂O₃ has the least stable surface. This is explained with the difference in the atomic configuration of each of these surfaces which induces a difference in their thermal decomposition. [reprint (PDF)]
17.	Semiconductor ultraviolet detectors M. Razeghi and A. Rogalski SPIE Photonics West '96 Photodetectors: Materials and Devices; Proceedings 2685-- January 27, 1996 ...[Visit Journal] This paper presents an overview of semiconductor ultraviolet (UV) detectors that are currently available and associated technologies that are undergoing further development. At the beginning, the classification of UV detectors and general requirements imposed on these detectors are presented. Further consideration are restricted to modern semiconductor UV detectors, so the current state-of-the-art of different types of semiconductor UV detectors is presented. Hitherto, the semiconductor UV detectors have been mainly fabricated using Si. Industries such as the aerospace, automotive, petroleum, and others have continuously provided the impetus pushing the development of fringe technologies which are tolerant of increasingly high temperatures and hostile environments. As a result, the main effort are currently directed to a new generation of UV detectors fabricated from wide-band-gap semiconductors between them the most promising are diamond and AlGaN. The latest progress in development of AlGaN UV detectors is finally described in detail. [reprint (PDF)]
17.	High Power 280 nm AlGaN Light Emitting Diodes Based on an Asymmetric Single Quantum Well K. Mayes, A. Yasan, R. McClintock, D. Shiell, S.R. Darvish, P. Kung, and M. Razeghi Applied Physics Letters, 84 (7)-- February 16, 2004 ...[Visit Journal] We demonstrate high-power AlGaN-based ultraviolet light-emitting diodes grown on sapphire with an emission wavelength of 280 nm using an asymmetric single-quantum-well active layer configuration on top of a high-quality AlGaN/AlN template layer. An output power of 1.8 mW at a pulsed current of 400 mA was achieved for a single 300 µm×300 µm diode. This device reached a high peak external quantum efficiency of 0.24% at 40 mA. An array of four diodes produced 6.5 mW at 880 mA of pulsed current. [reprint (PDF)]
17.	High-performance bias-selectable dual-band Short-/Mid-wavelength infrared photodetectors and focal plane arrays based on InAs/GaSb/AlSb Type-II superlattices M. Razeghi; A.M. Hoang; A. Haddadi; G. Chen; S. Ramezani-Darvish; P. Bijjam; P. Wijewarnasuriy; E. Decuir Proc. SPIE 8704, Infrared Technology and Applications XXXIX, 87041W (June 18, 2013)-- June 18, 2013 ...[Visit Journal] We report a bias selectable dual-band Type-II superlattice-based short-wave infrared (SWIR) and mid-wave infrared (MWIR) co-located photodetector capable of active and passive imaging. A new double-layer etch-stop scheme is introduced for back-side-illuminated photodetectors, which enhanced the external quantum efficiency both in the SWIR and MWIR spectral regions. Temperature-dependent dark current measurements of pixel-sized 27 μm detectors found the dark current density to be ∼1×10-5 A/cm2 for the ∼4.2 μm cut-off MWIR channel at 140 K. This corresponded to a reasonable imager noise equivalent difference in temperature of ∼49 mK using F/2.3 optics and a 10 ms integration time (tint), which lowered to ∼13 mK at 110 K using and integration time of 30 ms, illustrating the potential for high-temperature operation. The SWIR channel was found to be limited by readout noise below 150 K. An excellent imagery from the dual-band imager exemplifying pixel coincidence is shown. [reprint (PDF)]
17.	Room temperature continuous wave operation of λ ~ 3-3.2 μm quantum cascade lasers N. Bandyopadhyay, Y. Bai, S. Tsao, S. Nida, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 101, No. 24, p. 241110-1-- December 10, 2012 ...[Visit Journal] We demonstrate quantum cascade lasers emitting at wavelengths of 3–3.2 μm in the InP-based material system. The laser core consists of GaInAs/AlInAs using strain balancing technique. In room temperature pulsed mode operation, threshold current densities of 1.66 kA∕cm² and 1.97 kA∕cm², and characteristic temperatures (T₀) of 108 K and 102 K, are obtained for the devices emitting at 3.2 μm and 3 μm, respectively. Room temperature continuous wave operation is achieved at both wavelengths. [reprint (PDF)]
17.	High performance antimony based type-II superlattice photodiodes on GaAs substrates B.M. Nguyen, D. Hoffman, E.K. Huang, P.Y. Delaunay, and M. Razeghi SPIE Porceedings, Vol. 7298, Orlando, FL 2009, p. 72981T-- April 13, 2009 ...[Visit Journal] In recent years, Type-II InAs/GaSb superlattices grown on GaSb substrate have achieved significant advances in both structural design and material growth, making Type-II superlattice infrared detector a rival competitor to the state-of-the-art MCT technology. However, the limited size and strong infrared absorption of GaSb substrates prevent large format type-II superlattice infrared imagers from being realized. In this work, we demonstrate type-II superlattices grown on GaAs substrates, which is a significant step toward third generation infrared imaging at low cost. The device performances of Type-II superalttice photodetectors grown on these two substrates are compared. [reprint (PDF)]
17.	Long Wavelength Type-II Photodiodes Operating at Room Temperature H. Mohseni and M. Razeghi IEEE Photonics Technology Letters 13 (5)-- May 1, 2001 ...[Visit Journal] The operation of uncooled InAs-GaSb superlattice photodiodes with a cutoff wavelength of λc=8 μm and a peak detectivity of 1.2 × 10⁸ cm·Hz^½/W at zero bias is demonstrated. The detectivity is similar to the best uncooled HgCdTe detectors and microbolometers. However, the R0A product is more than two orders of magnitude higher than HgCdTe and the device is more than four orders of magnitude faster than microbolometers. These features combined with their low 1/f noise and high uniformity make these type-II photodiodes an excellent choice for uncooled high-speed IR imaging arrays [reprint (PDF)]
17.	Quantum cascade lasers that emit more light than heat Y. Bai, S. Slivken, S. Kuboya, S.R. Darvish and M. Razeghi Nature Photonics, February 2010, Vol. 4, p. 99-102-- February 1, 2010 ...[Visit Journal] For any semiconductor lasers, the wall plug efficiency, that is, the portion of the injected electrical energy that can be converted into output optical energy, is one of the most important figures of merit. A device with a higher wall plug efficiency has a lower power demand and prolonged device lifetime due to its reduced self-heating. Since its invention, the power performance of the quantum cascade laser has improved tremendously. However, although the internal quantum efficiency can be engineered to be greater than 80% at low temperatures, the wall plug efficiency of a quantum cascade laser has never been demonstrated above 50% at any temperature. The best wall plug efficiency reported to date is 36% at 120 K. Here, we overcome the limiting factors using a single-well injector design and demonstrate 53% wall plug efficiency at 40 K with an emitting wavelength of 5 µm. In other words, we demonstrate a quantum cascade laser that produces more light than heat. [reprint (PDF)]
17.	Broadband monolithically-tunable quantum cascade lasers Wenjia Zhou, Ryan McClintock, Donghai Wu, Steven Slivken, Manijeh Razeghi Proc. SPIE 10540, Quantum Sensing and Nano Electronics and Photonics XV, 105400A-- January 26, 2018 ...[Visit Journal] Mid-infrared lasers, emitting in the spectral region of 3-12 μm that contain strong characteristic vibrational transitions of many important molecules, are highly desirable for spectroscopy sensing applications. High efficiency quantum cascade lasers have been demonstrated with up to watt-level output power in the mid-infrared region. However, the wide wavelength tuning, which is critical for spectroscopy applications, is still largely relying on incorporating external gratings, which have stability issues. Here, we demonstrate the development a monolithic, widely tunable quantum cascade laser source emitting between 6.1 and 9.2 μm through an on-chip integration of a sampled grating distributed feedback tunable laser array with a beam combiner. A compact tunable laser system was built to drive the individual lasers within the array and coordinate the driving of the laser array to produce desired wavelength. A broadband spectral measurement (520cm^-1) of methane shows excellent agreement with Fourier transform infrared spectrometer measurement. Further optimizations have led to high performance monolithic tunable QCLs with up to 65 mW output while delivering fundamental mode outputs. [reprint (PDF)]
17.	Long-Wavelength InAsSb Photoconductors Operated at Near Room Temperatures (200-300 K) J.D. Kim, D. Wu, J. Wojkowski, J. Piotrowski, J. Xu, and M. Razeghi Applied Physics Letters., 68 (1),-- January 1, 1996 ...[Visit Journal] Long-wavelength InAs_1−xSb_x photoconductors operated without cryogenic cooling are reported. The devices are based on p-InAs_1−xSb_x/p-InSb heterostructures grown on (100) semi-insulating GaAs substrates by low pressure metalorganic chemical vapor deposition (LP‐MOCVD). Photoreponse up to 14 μm has been obtained in a sample with x=0.77 at 300 K, which is in good agreement with the measured infrared absorption spectra. The corresponding effective lifetime of ≊0.14 ns at 300 K has been derived from stationary photoconductivity. The Johnson noise limited detectivity at λ=10.6 μm is estimated to be about 3.27×10⁷ cm· Hz^½/W at 300 K. [reprint (PDF)]
17.	InSb Infrared Photodetectors on Si Substrates Grown by Molecular Beam Epitaxy E. Michel, J. Xu, J.D. Kim, I. Ferguson, and M. Razeghi IEEE Photonics Technology Letters 8 (5) pp. 673-- May 1, 1996 ...[Visit Journal] The InSb infrared photodetectors grown heteroepitaxially on Si substrates by molecular beam epitaxy (MBE) are reported. Excellent InSb material quality is obtained on 3-in Si substrates (with a GaAs predeposition) as confirmed by structural, optical, and electrical analysis. InSb infrared photodetectors on Si substrates that can operate from 77 K to room temperature have been demonstrated. The peak voltage-responsitivity at 4 μm is about 1.0×10³ V/W and the corresponding Johnson-noise-limited detectivity is calculated to be 2.8×10¹⁰ cm·Hz^½/W. This is the first important stage in developing InSb detector arrays or monolithic focal plane arrays (FPAs) on silicon. The development of this technology could provide a challenge to traditional hybrid FPA's in the future. [reprint (PDF)]
17.	High performance monolithic, broadly tunable mid-infrared quantum cascade lasers WENJIA Zhou, DONGHAI Wu, RYAN McCLINTOCK, STEVEN SLIVKEN, AND MANIJEH RAZEGH1 Optica 4(10), p. 1228-- October 10, 2017 ...[Visit Journal] Mid-infrared lasers, emitting in the spectral region of 3-12 µm that contains strong characteristic vibrational transitions of many important molecules, are highly desirable for spectroscopy sensing applications. High-efficiency quantum cascade lasers have been demonstrated with up to watt-level output power in the mid-infrared region. However, the wide wavelength tuning that is critical for spectroscopy applications still largely relies on incorporating external gratings, which have stability issues. Here, we demonstrate a monolithic, broadly tunable quantum cascade laser source emitting between 6.1 and 9.2 µm through an on-chip integration of a sampled grating distributed feedback tunable laser array and a beam combiner. High peak power up to 65 mW has been obtained through a balanced high-gain active region design, efficient waveguide layout, and the development of a broadband antireflection coating. Nearly fundamental transversemode operation is achieved for all emission wavelengths with a pointing stability better than 1.6 mrad (0.1 °). The demonstrated laser source opens new opportunities for mid-infrared spectroscopy. [reprint (PDF)]
16.	Demonstration of high performance long wavelength infrared Type-II InAs/GaSb superlattice photodidoe grown on GaAs substrate S. Abdollahi Pour, B.M. Nguyen, S. Bogdanov, E.K. Huang, and M. Razeghi Applied Physics Letters, Vol. 95, No. 17, p. 173505-- October 26, 2009 ...[Visit Journal] We report the growth and characterization of long wavelength infrared type-II InAs/GaSb superlattice photodiodes with a 50% cut-off wavelength at 11 µm, on GaAs substrate. Despite a 7.3% lattice mismatch to the substrate, photodiodes passivated with polyimide exhibit an R₀A value of 35 Ω·cm² at 77 K, which is in the same order of magnitude as reference devices grown on native GaSb substrate. With a reverse applied bias less than 500 mV, the dark current density and differential resistance-area product are close to that of devices on GaSb substrate, within the tolerance of the processing and measurement. The quantum efficiency attains the expected value of 20% at zero bias, resulting in a Johnson limited detectivity of 1.1×10¹¹ Jones. Although some difference in performances is observed, devices grown on GaAs substrate already attained the background limit performance at 77 K with a 300 K background and a 2-π field of view. [reprint (PDF)]
16.	Antimonide-Based Type II Superlattices: A Superior Candidate for the Third Generation of Infrared Imaging Systems M. Razeghi, A. Haddadi, A.M. Hoang, G. Chen, S. Bogdanov, S.R. Darvish, F. Callewaert, P.R. Bijjam, and R. McClintock Journal of ELECTRONIC MATERIALS, Vol. 43, No. 8, 2014-- August 1, 2014 ...[Visit Journal] Type II superlattices (T2SLs), a system of interacting multiquantum wells,were introduced by Nobel Laureate L. Esaki in the 1970s. Since then, this material system has drawn a lot of attention, especially for infrared detection and imaging. In recent years, the T2SL material system has experienced incredible improvements in material growth quality, device structure design, and device fabrication techniques that have elevated the performance of T2SL-based photodetectors and focal-plane arrays (FPAs) to a level comparable to state-of-the-art material systems for infrared detection and imaging, such as mercury cadmium telluride compounds. We present the current status of T2SL-based photodetectors and FPAs for imaging in different infrared regimes, from short wavelength to very long wavelength, and dual-band infrared detection and imaging, as well as the future outlook for this material system. [reprint (PDF)]
16.	High-Power (~9 μm) Quantum Cascade Lasers S. Slivken, Z. Huang, A. Evans, and M. Razeghi Virtual Journal of Nanoscale Science and Technology 5 (22)-- June 3, 2002 ...[Visit Journal][reprint (PDF)]
16.	Fabrication of GaN Nanotubular Material using MOCVD with an Aluminium Oxide Membrane W.G. Jung, S.H. Jung, P. Kung, and M. Razeghi Nanotechnology 17-- January 1, 2006 ...[Visit Journal] GaN nanotubular material is fabricated with an aluminium oxide membrane in MOCVD. SEM, XRD, TEM and PL are employed to characterize the fabricated GaN nanotubular material. An aluminium oxide membrane with ordered nanoholes is used as a template. Gallium nitride is deposited at the inner wall of the nanoholes in the aluminium oxide template, and the nanotubular material with high aspect ratio is synthesized using the precursors of TMG and ammonia gas. Optimal synthesis conditions in MOCVD are obtained successfully for the gallium nitride nanotubular material in this research. The diameter of the GaN nanotube fabricated is approximately 200–250 nm and the wall thickness is about 40–50 nm. [reprint (PDF)]
16.	Growth and characterization of InAs/GaSb photoconductors for long wavelength infrared range H. Mohseni, E. Michel, J. Sandven, M. Razeghi, W. Mitchel, and G. Brown Applied Physics Letters 71 (10)-- September 8, 1997 ...[Visit Journal] In this letter we report the molecular beam epitaxial growth and characterization of InAs/GaSb superlattices grown on semi-insulating GaAs substrates for long wavelength infrared detectors. Photoconductive detectors fabricated from the superlattices showed photoresponse up to 12 µm and peak responsivity of 5.5 V/W with Johnson noise limited detectivity of 1.33 × 10⁹ cm·Hz^½/W at 10.3 µm at 78 K. [reprint (PDF)]

Page 5 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)