Center for Quantum Devices - Most Downloaded Journal Articles

Page 25 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (737 Items)

12.	The correlation between x-ray diffraction patterns and strain distribution inside GaInP/GaAs superlattices X.G. He, M. Erdtmann, R. Williams, S. Kim, and M. Razeghi Applied Physics Letters 65 (22)-- November 28, 1994 ...[Visit Journal] Strong correlation between x‐ray diffraction characteristics and strain distribution inside GaInP/GaAs superlattices has been reported. It is found that the symmetry of (002) diffraction patterns can be used to evaluate the interface strain status. A sample with no interfacial strains has a symmetric (002) diffraction pattern and weak (004) diffraction pattern. It is also demonstrated that strain distribution in superlattices can be readily estimated qualitatively by analyzing x-ray diffraction patterns. [reprint (PDF)]
12.	High Performance Quantum Cascade Laser Results at the Centre for Quantum Devices M. Razeghi and S. Slivken Physica Status Solidi, 195 (1)-- January 1, 2003 ...[Visit Journal] In this paper, we review some of the history and recent results related to the development of the quantum cascade laser at the Center for Quantum Devices. The fabrication of the quantum cascade laser is described relative to growth, characterization, and processing. State-of-the-art testing results for 5-11 μm lasers will be then be explored, followed by a future outlook for the technology. [reprint (PDF)]
12.	Back-illuminated separate absorption and multiplication GaN avalanche photodiodes J.L. Pau, C. Bayram, R. McClintock, M. Razeghi and D. Silversmith Applied Physics Letters, Vol. 92, No. 10, p. 101120-1-- March 10, 2008 ...[Visit Journal] The performance of back-illuminated avalanche photodiodes with separate absorption and multiplication regions is presented. Devices with an active area of 225 µm² show a maximum multiplication gain of 41,200. The calculation of the noise equivalent power yields a minimum value of 3.3×10⁻¹⁴ W·Hz^−1/2 at a gain of 3000, increasing to 2.0×10⁻¹³ W·Hz^−1/2 at a gain of 41,200. The broadening of the response edge has been analyzed as a function of bias. [reprint (PDF)]
12.	Gain-length scaling in quantum dot/quantum well infrared photodetectors T. Yamanaka, B. Movaghar, S. Tsao, S. Kuboya, A. Myzaferi and M. Razeghi Virtual Journal of Nanoscale Science & Technology-- September 14, 2009 ...[Visit Journal][reprint (PDF)]
12.	First room‐temperature cw operation of a GaInAsP/InP light‐emitting diode on a silicon substrate M. Razeghi; R. Blondeau; M. Defour; F. Omnes; P. Maurel; F. Brillouet Appl. Phys. Lett. 53, 854–855 (1988)-- July 4, 1988 ...[Visit Journal] We report in this letter the first successful fabrication of an InP-GalnAsP light-emitting diode, emitting at 1.15 pm grown by low-pressure metalorganic chemical vapor deposition on a silicon substrate. The device has been operated under continuous wave operation at room temperature for 24 h (with an injection current of 200 rnA), and showed no degradation. [reprint (PDF)]
12.	Passivation of Type-II InAs/GaSb Superlattice Photodiodes A. Gin, Y. Wei, J. Bae, A. Hood, J. Nah, and M. Razeghi International Conference on Metallurgical Coatings and Thin Films (ICMCTF), San Diego, CA; Thin Solid Films 447-448-- January 30, 2004 ...[Visit Journal] Recently, excellent infrared detectors have been demonstrated using Type-II InAs/GaSb superlattice materials sensitive at wavelengths from 3 μm to greater than 32 μm. These results indicate that Type-II superlattice devices may challenge the preponderance of HgCdTe and other state-of-the-art infrared material systems. As such, surface passivation is becoming an increasingly important issue as progress is made towards the commercialization of Type-II devices and focal plane array applications. This work focuses on initial attempts at surface passivation of Type-II InAs/GaSb superlattice photodiodes using PECVD-grown thin layers of SiO₂. Our results indicate that silicon dioxide coatings deposited at various temperatures improve photodetector resistivity by several times. Furthermore, reverse-bias dark current has been reduced significantly in passivated devices. [reprint (PDF)]
12.	High‐purity GaAs layers grown by low‐pressure metalorganic chemical vapor deposition M. Razeghi; F. Omnes; J. Nagle; M. Defour; O. Acher; P. Bove Appl. Phys. Lett. 55, 1677–1679 (1989)-- October 16, 1989 ...[Visit Journal] We report electrical and optical properties of very high purity GaAs epilayers grown by low‐pressure metalorganic chemical vapor deposition using AsH3 and triethylgallium as As and Ga sources. An electron mobility of 335 000 cm2/V s at 38 K has been measured for a 12‐μ‐thick layer. [reprint (PDF)]
12.	Noise analysis in type-II InAs/GaSb focal plane arrays P.Y. Delaunay and M. Razeghi Journal of Applied Physics, Vol. 106, Issue 6, p. 063110-- September 15, 2009 ...[Visit Journal] A long wavelength infrared focal plane array based on type-II InAs/GaSb superlattices was fabricated and characterized at 80 K. The noise equivalent temperature difference in the array was measured as low as 23 mK for an integration time of 0.129 ms. The noise behavior of the detectors was properly described by a model based on thermal, shot, read out integrated circuit, and photon noises. The noise of the imager was dominated by photon noise for photon fluxes higher than 1.8×10¹⁵ ph·s⁻¹·cm⁻². At lower irradiance, the imager was limited by the shot noise generated by the dark current or the noise of the testing system. The superlattice detector did not create 1/f noise for frequencies above 4 mHz. As a result, the focal plane array did not require frequent calibrations. [reprint (PDF)]
12.	Widely Tunable, Single-Mode, High-Power Quantum Cascade Lasers M. Razeghi, B. Gokden, S. Tsao, A. Haddadi, N. Bandyopadhyay, and S. Slivken SPIE Proceedings, Intergreated Photonics: Materials, Devices and Applications, SPIE Microtechnologies Symposium, Prague, Czech Republic, April 18-20, 2011, Vol. 8069, p. 806905-1-- May 31, 2011 ...[Visit Journal] We demonstrate widely tunable high power distributed feedback quantum cascade laser array chips that span 190 nm and 200 nm from 4.4 um to 4.59 um and 4.5 um to 4.7 um respectively. The lasers emit single mode with a very narrow linewidth and side mode suppression ratio of 25 dB. Under pulsed operation power outputs up to 1.85 W was obtained from arrays with 3 mm cavity length and up to 0.95 W from arrays with 2 mm cavity length at room temperature. Continuous wave operation was also observed from both chips with 2 mm and 3 mm long cavity arrays up to 150 mW. The cleaved size of the array chip with 3 mm long cavities was around 4 mm x 5 mm and does not require sensitive external optical components to achieve wide tunability. With their small size and high portability, monolithically integrated DFB QCL Arrays are prominent candidates of widely tunable, compact, efficient and high power sources of mid-infrared radiation for gas sensing. [reprint (PDF)]
12.	Improved performance of quantum cascade lasers via manufacturable quality epitaxial side down mounting process utilizing aluminum nitride heatsinks A. Tsekoun, R. Go, M. Pushkarsky, M. Razeghi, C.K.N. Patel SPIE Conference, San Jose, CA, Vol. 6127, pp. 612702-- January 23, 2006 ...[Visit Journal] We report substantially improved performance of high power quantum cascade lasers by utilizing epi-side down mounting that provides superior heat dissipation properties. We have obtained CW power output of 450 mW at 20°C from mid-IR QCLs. The improved thermal management achieved with epi-side down mounting has also permitted us to carry out initial lifetime tests on the mid-IR QCLs. No degradation of power output is seen even after over 300 hours of CW operation at 25°C with power output in excess of 300 mW. We believe these improvements should permit incorporation of mid-IR QCLs in reliable instrumentation. [reprint (PDF)]
12.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, S.R. Darvish, S. Slivken, P. Sung, J. Nguyen, A. Evans, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 91, No. 14, p. 141123-1-- October 1, 2007 ...[Visit Journal] We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~4.75 µm. Ridge waveguides of 100 µm width were fabricated with both PCDFB and Fabry-Pérot feedback mechanisms. The Fabry-Pérot device has a broad emitting spectrum and a double lobed far-field character. The PCDFB device, as expected, has primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half maximum of 2.4°. This accomplishment represents the first step in power scaling of single mode, midinfrared laser diodes operating at room temperature. [reprint (PDF)]
12.	Temperature dependent characteristics of λ ~ 3.8 µm room-temperature continuous-wave quantum-cascade lasers J.S. Yu, A. Evans, S. Slivken, S.R. Darvish and M. Razeghi Applied Physics Letters, 88 (25)-- June 19, 2006 ...[Visit Journal] The highest-performance device displays pulsed laser action at wavelengths between 3.4 and 3.6 μm, for temperatures up to 300 K, with a low temperature (80 K) threshold current density of approximately 2.6 kA/cm², and a characteristic temperature of T₀~130 K. The shortest wavelength QCL (λ ~ 3.05 μm) has a higher threshold current density (~12 kA/cm² at T=20 K) and operates in pulsed mode at temperatures up to 110 K. [reprint (PDF)]
12.	Shortwave quantum cascade laser frequency comb for multi-heterodyne spectroscopy Q. Y. Lu, S. Manna, D. H. Wu, S. Slivken, and M. Razeghi Applied Physics Letters 112, 141104-- April 3, 2018 ...[Visit Journal] Quantum cascade lasers (QCLs) are versatile light sources with tailorable emitting wavelengths covering the mid-infrared and terahertz spectral ranges. When the dispersion is minimized, frequency combs can be directly emitted from quantum cascade lasers via four-wave mixing. To date, most of the mid-infrared quantum cascade laser combs are operational in a narrow wavelength range wherein the QCL dispersion is minimal. In this work, we address the issue of very high dispersion for shortwave QCLs and demonstrate 1-W dispersion compensated shortwave QCL frequency combs at λ~5.0 μm, spanning a spectral range of 100 cm⁻¹. The multi-heterodyne spectrum exhibits 95 equally spaced frequency comb lines, indicating that the shortwave QCL combs are ideal candidates for high-speed high-resolution spectroscopy [reprint (PDF)]
12.	MOCVD grown β-Ga₂O₃ metal-oxide-semiconductor field effect transistors on sapphire Ji-Hyeon Park , Ryan McClintock, Alexandre Jaud, Arash Dehzangi , Manijeh Razeghi Applied Physics Express 12, 095503-- August 28, 2019 ...[Visit Journal] We fabricated β-Ga₂O₃:Si metal-oxide field-effect transistors (MOSFETs) on c-plane sapphire substrates which typically showed maximum drain current of 100 mA·mm⁻¹. β-Ga₂O₃:Si thin films were realized on c-plane sapphire substrates through a combination of metalorganic chemical vapor deposition and post-annealing. The MOSFET device presented excellent on/off drain current ratio of ∼10¹¹ with very low gate leakage current, sharp pinch off behavior, and a breakdown voltage of 400 V at VG = −40 V. The growth and fabrication of β-Ga₂O₃:Si MOSFETs on c-plane sapphire is valuable to its demonstration of the great potential for future high-power electronic devices. [reprint (PDF)]
12.	III-Nitride Optoelectronic Devices: From Ultraviolet Toward Terahertz M. Razeghi IEEE Photonics Journal-Breakthroughs in Photonics 2010, Vol. 3, No. 2, p. 263-267-- April 26, 2011 ...[Visit Journal] We review III-Nitride optoelectronic device technologies with an emphasis on recent breakthroughs. We start with a brief summary of historical accomplishments and then report the state-of-the-art in three key spectral regimes: (1) Ultraviolet (AlGaN-based avalanche photodiodes, single photon detectors, focal plane arrays, and light emitting diodes), (2) Visible (InGaN-based solid state lighting, lasers, and solar cells), and (3) Near-, mid-infrared, and terahertz (AlGaN/GaN-based gap-engineered intersubband devices). We also describe future trends in III-Nitride optoelectronic devices. [reprint (PDF)]
11.	Optical losses of Al-free lasers for λ = 0.808 and 0.98 μm H. Yi, J. Diaz, B. Lane, and M. Razeghi Applied Physics Letters 69 (20)-- November 11, 1996 ...[Visit Journal] In this work, we study the origin of the optical losses in Al‐free InGaAsP/GaAs (λ=0.808 μm) and InGaAs/GaAs/InGaP (λ=0.980 μm) lasers. Theoretical modeling and the experimental results indicate that the scattering of the laser beam by refractive index fluctuation in the alloys is the dominant loss in our lasers, and the loss due to the free‐carrier absorption and scattering by interface roughness are negligible. [reprint (PDF)]
11.	Solar-blind AlGaN photodiodes with very low cutoff wavelength D. Walker, V. Kumar, K. Mi, P. Sandvik, P. Kung, X.H. Zhang, and M. Razeghi Applied Physics Letters 76 (4)-- January 24, 2000 ...[Visit Journal] We report the fabrication and characterization of AlxGa1–xN photodiodes (x~0.70) grown on sapphire by low-pressure metalorganic chemical vapor deposition. The peak responsivity for –5 V bias is 0.11 A/W at 232 nm, corresponding to an internal quantum efficiency greater than 90%. The device response drops four orders of magnitude by 275 nm and remains at low response for the entire near-ultraviolet and visible spectrum. Improvements were made to the device design including a semitransparent Ni/Au contact layer and a GaN:Mg cap layer, which dramatically increased device response by enhancing the carrier collection efficiency. [reprint (PDF)]
11.	Extended electrical tuning of quantum cascade lasers with digital concatenated gratings S. Slivken, N. Bandyopadhyay, Y. Bai, Q. Y. Lu, and M. Razeghi Appl. Phys. Lett. 103, 231110 (2013)-- December 6, 2013 ...[Visit Journal] In this report, the sampled grating distributed feedback laser architecture is modified with digital concatenated gratings to partially compensate for the wavelength dependence of optical gain in a standard high efficiency quantum cascade laser core. This allows equalization of laser threshold over a wide wavelength range and demonstration of wide electrical tuning. With only two control currents, a full tuning range of 500 nm (236 cm⁻¹) has been demonstrated. Emission is single mode, with a side mode suppression of >20 dB. [reprint (PDF)]
11.	High‐quality GaAs/Ga0.49In0.51P superlattices grown on GaAs and silicon substrates by low‐pressure metalorganic chemical vapor deposition Available M. Razeghi; Ph. Maurel; F. Omnes; M. Defour; C. Boothroyd; W. M. Stobbs; M. Kelly J. Appl. Phys. 63, 4511–4514 (1988) -- May 1, 1988 ...[Visit Journal] We report the successful growth of Ga0.49 Iuo.5 ! P-GaAs superlattices on GaAs and Si substrates by low-pressure metalorganic chemical vapor deposition. The high quality of the structure grown on GaAs and silicon substrates has been evidenced by transmission electron microscopy photographs, that show very sharp interfaces between GaAs wells and Gao.49InO.51 P barriers, with perfect control of thicknesses and compositions. Classical Hall measurements performed on the sample further demonstrated the presence of a twodimensional electron ga.<; with a mobility at T = 4 K , fL (4 K) = 50000 cm2 1V Is, and a carrier concentration n _ (4 K) = 2,9 X 1011 em -2. GaAs/Gao.49 InO. 51 P superlattices have been used, as well as buffer layer in order to grow GaAs on silicon substrates. Mirrorlike single-crystal GaAs has thus been obtained. A GaInP IGaAs heterostructure with electron HaH mobility as high as 6000 cm2 /V Is at 300 K and 80000 cm2 /V Is at 4 K has been grown, which is the highest mobility that has yet been reported for these materials, [reprint (PDF)]
11.	Investigation of 0.8 μm InGaAsP-GaAs laser diodes with Multiple Quantum Wells J. Diaz, H. Yi, S. Kim, M. Erdtmann, L.J. Wang, I. Eliashevich, E. Bigan and M. Razeghi Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995 ...[Visit Journal] In this paper, we studied the effects of the active region structure (one, two and three quantum wells with same total thickness) for high-power InGaAsP-GaAs separate confinement heterostructure lasers emitting at 0.8 μm wavelength. Experimental results for the lasers grown by low pressure metalorganic chemical vapor deposition show excellent agreement with the theoretical model. Total output power of 47 W from an uncoated 1 cm-wide laser bar was achieved in quasi-continuous wave operation [reprint (PDF)]
11.	Structural and compositional characterization of MOVPE GaN thin films transferred from sapphire to glass substrates using chemical lift-off and room temperature direct wafer bonding and GaN wafer scale MOVPE growth on ZnO-buffered sapphire S. Gautier, T. Moudakir, G. Patriarche, D.J. Rogers, V.E. Sandana, F. Hosseini Teherani, P. Bove, Y. El Gmili, K. Pantzas, Suresh Sundaram, D. Troadec, P.L. Voss, M. Razeghi, A. Ougazzaden Journal of Crystal Growth, Volume 370, Pages 63-67 (2013)-- May 1, 2013 ...[Visit Journal] GaN thin films were grown on ZnO/c-Al₂O₃ with excellent uniformity over 2 in. diameter wafers using a low temperature/pressure MOVPE process with N₂ as a carrier and dimethylhydrazine as an N source. 5 mm×5 mm sections of similar GaN layers were direct-fusion-bonded onto soda lime glass substrates after chemical lift-off from the sapphire substrates. X-Ray Diffraction, Scanning Electron Microscopy and Transmission Electron Microscopy confirmed the bonding of crack-free wurtzite GaN films onto a glass substrate with a very good quality of interface, i.e. continuous/uniform adherence and absence of voids or particle inclusions. Using this approach, (In) GaN based devices can be lifted-off expensive single crystal substrates and bonded onto supports with a better cost-performance profile. Moreover, the approach offers the possibility of reclaiming the expensive sapphire substrate so it can be utilized again for growth. [reprint (PDF)]
11.	GaInAsP/InP 1.35 μm Double Heterostructure Laser Grown on Silicon Substrate by Metalorganic Chemical Vapor Deposition K. Mobarhan, C. Jelen, E. Kolev, and M. Razeghi Journal of Applied Physics 74 (1)-- July 1, 1993 ...[Visit Journal] A 1.35 μm GaInAsP/InP double heterostructure laser has been grown on a Si substrate using low‐pressure metalorganic chemical vapor deposition. This was done without the use of a superlattice layer or a very thick InP buffer layer, which are used to prevent the dislocations from spreading into the active layer. Pulsed operation with output power of over 200 mW per facet was achieved at room temperature for broad area lasers with 20 μm width and 170 μm cavity length. The threshold current density of a 350 μm cavity length device was 9.8 kA/cm². The characteristic temperature was 66 K. [reprint (PDF)]
11.	Thermal conductivity tensors of the cladding and active layers of antimonide infrared lasers and detectors Chuanle Zhou, I. Vurgaftman, C. L. Canedy, C. S. Kim, M. Kim, W. W. Bewley, C. D. Merritt, J. Abell, J. R. Meyer, A. Hoang, A. Haddadi, M. Razeghi, and M. Grayson Optical Materials Express. 2013;3(10):1632-1640.-- October 1, 2013 ...[Visit Journal] The in-plane and cross-plane thermal conductivities of the cladding layers and active quantum wells of interband cascade lasers and type-II superlattice infrared detector are measured by the 2-wire 3ω method. The layers investigated include InAs/AlSb superlattice cladding layers, InAs/GaInSb/InAs/AlSb W-active quantum wells, an InAs/GaSb superlattice absorber, an InAs/GaSb/AlSb M-structure, and an AlAsSb digital alloy. The in-plane thermal conductivity of the InAs/AlSb superlattice is 4-5 times higher than the cross-plane value. The isotropic thermal conductivity of the AlAsSb digital alloy matches a theoretical expectation, but it is one order of magnitude lower than the only previously-reported experimental value. [reprint (PDF)]
11.	A hybrid green light-emitting diode comprised of n-ZnO/(InGaN/GaN) multi-quantum-wells/p-GaN C. Bayram, F. Hosseini Teherani, D.J. Rogers and M. Razeghi Applied Physics Letters, Vol. 93, No. 8, p. 081111-1-- August 25, 2008 ...[Visit Journal] Hybrid green light-emitting diodes (LEDs) comprised of n-ZnO/(InGaN/GaN) multi-quantum-wells/p-GaN were grown on semi-insulating AlN/sapphire using pulsed laser deposition for the n-ZnO and metal organic chemical vapor deposition for the other layers. X-ray diffraction revealed that high crystallographic quality was preserved after the n-ZnO growth. LEDs showed a turn-on voltage of 2.5 V and a room temperature electroluminescence (EL) centered at 510 nm. A blueshift and narrowing of the EL peak with increasing current was attributed to bandgap renormalization. The results indicate that hybrid LED structures could hold the prospect for the development of green LEDs with superior performance. [reprint (PDF)]
11.	Room temperature quantum cascade lasers with 22% wall plug efficiency in continuous-wave operation F. Wang, S. Slivken, D. H. Wu, and M. Razeghi Optics Express Vol. 28, Issue 12, pp. 17532-17538-- June 8, 2020 ...[Visit Journal] We report the demonstration of quantum cascade lasers (QCLs) with improved eﬃciency emitting at a wavelength of 4.9 µm in pulsed and continuous-wave(CW)operation. Based on an established design and guided by simulation, the number of QCL-emitting stages is increased in order to realize a 29.3% wall plug eﬃciency (WPE) in pulsed operation at room temperature. With proper fabrication and packaging, a 5-mm-long, 8-µm-wide QCL with a buried ridge waveguide is capable of 22% CW WPE and 5.6 W CW output power at room temperature. This corresponds to an extremely high optical density at the output facet of ∼35 MW/cm², without any damage. [reprint (PDF)]

Page 25 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (737 Items)