Center for Quantum Devices - Most Downloaded Journal Articles

Page 24 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (736 Items)

10.	InAsSb/InAsP strained-layer superlattice injection lasers operating at 4.0 μm grown by metal-organic chemical vapor deposition B. Lane, Z. Wu, A. Stein, J. Diaz, and M. Razeghi Applied Physics Letters 74 (23)-- June 7, 1999 ...[Visit Journal] We report high power mid-infrared electrical injection operation of laser diodes based on InAsSb/InAsP strained-layer superlattices grown on InAs substrate by metal-organic chemical vapor deposition. The broad-area laser diodes with 100 μm aperture and 1800 μm cavity length demonstrate peak output powers of 546 and 94 mW in pulsed and cw operation respectively at 100 K with a threshold current density as low as 100 A/cm². [reprint (PDF)]
10.	Ultraviolet Detector Materials and Devices Studied by Femtosecond Nonlinear Optical Techniques M. Wraback, H. Shen, P. Kung, M. Razeghi, J.C. Carrano, T. Li, and J.C. Campbell SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] Femtosecond nonlinear optical techniques have been employed in the study of carrier dynamics and transport in UV detector materials. Visible femtosecond pulses derived from the signal beam of a 250 kHz regenerative amplifier-pumped optical parametric amplifier were frequency doubled to obtain pulses tunable from 250 nm to 375 nm. Time-resolved reflectivity experiments indicate that the room-temperature carrier lifetime in GaN grown by double lateral epitaxial overgrowth is about 3 times longer than that of GaN grown on sapphire without benefit of this technique. The electron velocity-field characteristics and saturation velocity in GaN have been obtained form time-resolved studies of electroabsorption in a GaN p-i-n diode. The peak steady- state velocity of 1.9x10⁷ cm/s in this device occurs at 225 kV/cm. Time-resolved transmission measurements have been used to monitor ultrafast carrier relaxation phenomena in a thin AlGaN layer with bandgap in the solar blind region of the spectrum. Excitation intensity and wavelength dependent studies of the photoinduced bleaching decays suggest that they are primarily governed by trapping in a high density of sub-bandgap defect levels. [reprint (PDF)]
10.	Quantum oscillations at a Ga0.47In0.53AsInP heterojunction interface R.J Nicholas a, M.A Brummell a , J.C Portal b, M Razeghi c, M.A Poisson R.J Nicholas, M.A Brummell, J.C Portal, M Razeghi, M.A Poisson, Quantum oscillations at a Ga0.47In0.53AsInP heterojunction interface, Solid State Communications, Volume 43, Issue 11, 1982, Pages 825-828,-- September 1, 1982 ...[Visit Journal] We report the observation of a two dimensional gas of high mobility electrons at the interface of a Ga0.47In0.53AsInP heterojunction grown by MOCVD. The two dimensional electron concentrations and effective mass are determined by Shubnikov-de Haas studies, and compared with theoretical predictions. Evidence of an enhancement of the g-factor is observed. We also report observations of very pronounced quantum Hall steps as seen in GaAs-GaAlAs heterojunctions. [reprint (PDF)]
10.	Widely Tunable, Single-Mode, High-Power Quantum Cascade Lasers M. Razeghi, B. Gokden, S. Tsao, A. Haddadi, N. Bandyopadhyay, and S. Slivken SPIE Proceedings, Intergreated Photonics: Materials, Devices and Applications, SPIE Microtechnologies Symposium, Prague, Czech Republic, April 18-20, 2011, Vol. 8069, p. 806905-1-- May 31, 2011 ...[Visit Journal] We demonstrate widely tunable high power distributed feedback quantum cascade laser array chips that span 190 nm and 200 nm from 4.4 um to 4.59 um and 4.5 um to 4.7 um respectively. The lasers emit single mode with a very narrow linewidth and side mode suppression ratio of 25 dB. Under pulsed operation power outputs up to 1.85 W was obtained from arrays with 3 mm cavity length and up to 0.95 W from arrays with 2 mm cavity length at room temperature. Continuous wave operation was also observed from both chips with 2 mm and 3 mm long cavity arrays up to 150 mW. The cleaved size of the array chip with 3 mm long cavities was around 4 mm x 5 mm and does not require sensitive external optical components to achieve wide tunability. With their small size and high portability, monolithically integrated DFB QCL Arrays are prominent candidates of widely tunable, compact, efficient and high power sources of mid-infrared radiation for gas sensing. [reprint (PDF)]
10.	Room temperature quantum cascade lasers with 27% wall plug efficiency Y. Bai, N. Bandyopadhyay, S. Tsao, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 98, No. 18, p. 181102-1-- May 3, 2011 ...[Visit Journal] Using the recently proposed shallow-well design, we demonstrate InP based quantum cascade lasers (QCLs) emitting around 4.9 μm with 27% and 21% wall plug efficiencies in room temperature (298 K) pulsed and continuous wave (CW) operations, respectively. The laser core consists of 40 QCL-stages. The highest cw efficiency is obtained from a buried-ridge device with a ridge width of 8 μm and a cavity length of 5 mm. The front and back facets are antireflection and high-reflection coated, respectively. The maximum single facet cw power at room temperature amounts to 5.1 W. [reprint (PDF)]
10.	Dark current reduction in microjunction-based compound electron barrier type-II InAs/InAs1-xSbx superlattice-based long-wavelength infrared photodetectors Romain Chevallier, Abbas Haddadi, Manijeh Razeghi Proc. SPIE 10540, Quantum Sensing and Nano Electronics and Photonics XV Page. 1054007-1-- January 26, 2018 ...[Visit Journal] Reduction of dark current density in microjunction-based InAs/InAs_1-xSb_x type-II superlattice long-wavelength infrared photodetectors was demonstrated. A double electron barrier design was used to suppress both generation-recombination and surface dark currents. The photodetectors exhibited high surface resistivity after passivation with SiO₂, which permits the use of small size features without having strong surface leakage current degrading the electrical performance. Fabricating a microjunction structure (25×25 μm² mesas with 10×10 μm² microjunctions) with this photodetector double barrier design results in a dark current density of 6.3×10^-6 A/cm² at 77 K. The device has an 8 μm cut-off wavelength at 77 K and exhibits a quantum efficiency of 31% for a 2 μm-thick absorption region, which results in a specific detectivity value of 1.2×10¹² cm·Hz^1/2/W at 77 K. [reprint (PDF)]
10.	Single-mode, high-power, midinfrared, quantum cascade laser phased arrays Wenjia Zhou , Donghai Wu , Quan-Yong Lu, Steven Slivken & Manijeh Razeghi Scientific Reports 8:14866-- October 5, 2018 ...[Visit Journal] We demonstrate single-mode, 16-channel, optical phased arrays based on quantum cascade laser technology, with emission wavelengths around 4.8 μm. The integrated device consists of a distributed feedback seed section, a highly-efficient tree array multi-mode interferometer power splitter, and a 16-channel amplifier array with a 4° angled facet termination. With a single layer Y₂O₃ coating, the angled facet reflectivity is estimated to be less than 0.1% for suppressing amplifier self-lasing. A peak output power of 30 W is achieved with an emission spectrum narrower than 11 nm and a side mode suppression ratio over 25 dB. Far field distribution measurement result indicates a uniform phase distribution across the array output. Using the same phased array architecture, we also demonstrate single-mode 3.8 μm QCL amplifier arrays with up to 20 W output power. [reprint (PDF)]
10.	High‐purity GaAs layers grown by low‐pressure metalorganic chemical vapor deposition M. Razeghi; F. Omnes; J. Nagle; M. Defour; O. Acher; P. Bove Appl. Phys. Lett. 55, 1677–1679 (1989)-- October 16, 1989 ...[Visit Journal] We report electrical and optical properties of very high purity GaAs epilayers grown by low‐pressure metalorganic chemical vapor deposition using AsH3 and triethylgallium as As and Ga sources. An electron mobility of 335 000 cm2/V s at 38 K has been measured for a 12‐μ‐thick layer. [reprint (PDF)]
10.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, S.R. Darvish, S. Slivken, P. Sung, J. Nguyen, A. Evans, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 91, No. 14, p. 141123-1-- October 1, 2007 ...[Visit Journal] We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~4.75 µm. Ridge waveguides of 100 µm width were fabricated with both PCDFB and Fabry-Pérot feedback mechanisms. The Fabry-Pérot device has a broad emitting spectrum and a double lobed far-field character. The PCDFB device, as expected, has primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half maximum of 2.4°. This accomplishment represents the first step in power scaling of single mode, midinfrared laser diodes operating at room temperature. [reprint (PDF)]
10.	Type-II superlattice-based heterojunction phototransistors for high speed applications Jiakai Li, Arash Dehzangi, Donghai Wu, Ryan McClintock, Manijeh Razeghi Infrared Physics and Technology 108, 1033502-- May 2, 2020 ...[Visit Journal] In this study, high speed performance of heterojunction phototransistors (HPTs) based on InAs/GaSb/AlSb type-II superlattice with 30 nm base thickness and 50% cut-off wavelength of 2.0 μm at room temperature are demonstrated. We studied the relationship between -3 dB cut-off frequency of these HPT versus mesa size, applied bias, and collector layer thickness. For 8 μm diameter circular mesas HPT devices with a 0.5 μm collector layer, under 20 V applied bias voltage, we achieved a -3 dB cut-off frequency of 2.8 GHz. [reprint (PDF)]
10.	High Performance Type-II InAs/GaSb Superlattice Photodiodes H. Mohseni, Y. Wei, and M. Razeghi SPIE Conference, San Jose, CA, -- January 22, 2001 ...[Visit Journal] We report on the demonstration of high performance p-i-n photodiodes based on Type-II InAs/GaSb superlattices operating in the very long wavelength infrared (VLWIR) range at 80 K. Material is grown by molecular beam epitaxy on GaSb substrates with excellent crystal quality as evidenced by x-ray diffraction and atomic force microscopy. The processed devices with a 50% cutoff wavelength of λ_c equals 22 μm show a peak current responsivity about 5.5 A/W at 80 K. The use of binary layers in the superlattice has significantly enhanced the uniformity and reproducibility of the energy gap. The 90% to 10% cut-off energy width of these devices is on the order of 2 kT which is about four times smaller compared to the devices based on InAs/Ga1-xInxSb superlattices. Similar photovoltaic devices with cut-off wavelengths up to 25 μm have been measured at 80 K. Our experimental results shows excellent uniformity over a three inch wafer area, indicating the possibility of VLWIR focal plane arrays based on Type-II superlattices. [reprint (PDF)]
10.	Sharp/Tuneable UVC Selectivity and Extreme Solar Blindness in Nominally Undoped Ga2O3 MSM Photodetectors Grown by Pulsed Laser Deposition D. J. Rogers, A. Courtois, F. H. Teherani, V. E. Sandana, P. Bove, X. Arrateig, L. Damé, P. Maso, M. Meftah, W. El Huni, Y. Sama, H. Bouhnane, S. Gautier, A. Ougazzaden & M. Razeghi Proc. SPIE 11687 (2021) 116872D-1 ...[Visit Journal] Ga2O3layers were grown on c-sapphire substrates by pulsed laser deposition. Optical transmission spectra were coherent with a bandgap engineering from 4.9 to 6.2 eV controlled via the growth conditions. X-ray diffraction revealed that the films were mainly β-Ga2O3(monoclinic) with strong (-201) orientation. Metal-Semiconductor-Metal photodetectors based on gold/nickel Inter- Digitated-Transducer structures were fabricated by single-step negative photolithography. 240 nm peak response sensors gave over 2 orders-of-magnitude of separation between dark and light signal with state-of-the-art solar and visible rejection ratios ((I240 : I290) of > 3 x 105 and (I240 : I400) of > 2 x 106) and dark signals of <50 pA (at a bias of -5V). Spectral responsivities showed an exceptionally narrow linewidth (16.5 nm) and peak values exhibited a slightly superlinear increase with applied bias up to a value of 6.5 A/W (i.e. a quantum efficiency of > 3000%) at 20V bias. [reprint (PDF)]
10.	First room‐temperature cw operation of a GaInAsP/InP light‐emitting diode on a silicon substrate M. Razeghi; R. Blondeau; M. Defour; F. Omnes; P. Maurel; F. Brillouet Appl. Phys. Lett. 53, 854–855 (1988)-- July 4, 1988 ...[Visit Journal] We report in this letter the first successful fabrication of an InP-GalnAsP light-emitting diode, emitting at 1.15 pm grown by low-pressure metalorganic chemical vapor deposition on a silicon substrate. The device has been operated under continuous wave operation at room temperature for 24 h (with an injection current of 200 rnA), and showed no degradation. [reprint (PDF)]
10.	Ultraviolet avalanche photodiodes Ryan McClintock ; Manijeh Razeghi Proc. SPIE 9555, Optical Sensing, Imaging, and Photon Counting: Nanostructured Devices and Applications, 95550B -- August 28, 2015 ...[Visit Journal] The III-Nitride material system is rapidly maturing; having proved itself as a material for LEDs and laser, and now finding use in the area of UV photodetectors. However, many UV applications are still dominated by the use of photomultiplier tubes (PMT). PMTs are capable of obtaining very high sensitivity using internal electron multiplication gain (typically ~106). It is highly desirable to develop a compact semiconductor-based photodetector capable of realizing this level of sensitivity. In principle, this can be obtained in III-Nitrides by taking advantage of avalanche multiplication under high electric fields – typically 2.7 MV/cm, which with proper design can correspond to an external reverse bias of less than 100 volts. In this talk, we review the current state-of-the-art in III-Nitride solar- and visible-blind APDs, and present our latest results on GaN APDs grown on both conventional sapphire and low dislocation density free-standing c- and m-plane GaN substrates. Leakage current, gain, and single photon detection efficiency (SPDE) of these APDs were compared. The spectral response and Geiger-mode photon counting performance of UV APDs are studied under low photon fluxes, with single photon detection capabilities as much as 30% being demonstrated in smaller devices. Geiger-mode operation conditions are optimized for enhanced SPDE. [reprint (PDF)]
10.	Metalorganic chemical vapor deposition of monocrystalline GaN thin films on β-LiGaO2substrates P. Kung, A. Saxler, X. Zhang, D. Walker, R. Lavado, and M. Razeghi Applied Physics Letters 69 (14)-- September 30, 1996 ...[Visit Journal] We report the metalorganic chemical vapor deposition growth and characterization of monocrystalline GaN thin films on β-LiGaO₂ substrates. The influence of the growth temperature on the crystal quality was studied. The structural, electrical, and optical properties of the films were assessed through scanning electron microscopy, x-ray diffraction, Hall measurements, optical transmission, photoluminescence. [reprint (PDF)]
10.	Schottky MSM Photodetectors on GaN Films Grown on Sapphire by Lateral Epitaxial Overgrowth P. Kung, D. Walker, P. Sandvik, M. Hamilton, J. Diaz, I.H. Lee and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] We report the growth and characterization of Schottky based metal-semiconductor-metal ultraviolet photodetectors fabricated on lateral epitaxially overgrown GaN films. The lateral epitaxial overgrowth of GaN was carried out on basal plane sapphire substrates by low pressure metalorganic chemical vapor deposition and exhibited lateral growth rates more than 5 times as high as vertical growth rates. The spectral responsivity, the dependence on bias voltage, on incident optical power, and the time response of these photodetectors have been characterized. Two detector orientations were investigated: one with the interdigitated finger pattern parallel and the other perpendicular to the underlying SiO_x mask stripes. [reprint (PDF)]
10.	Improved performance of quantum cascade lasers via manufacturable quality epitaxial side down mounting process utilizing aluminum nitride heatsinks A. Tsekoun, R. Go, M. Pushkarsky, M. Razeghi, C.K.N. Patel SPIE Conference, San Jose, CA, Vol. 6127, pp. 612702-- January 23, 2006 ...[Visit Journal] We report substantially improved performance of high power quantum cascade lasers by utilizing epi-side down mounting that provides superior heat dissipation properties. We have obtained CW power output of 450 mW at 20°C from mid-IR QCLs. The improved thermal management achieved with epi-side down mounting has also permitted us to carry out initial lifetime tests on the mid-IR QCLs. No degradation of power output is seen even after over 300 hours of CW operation at 25°C with power output in excess of 300 mW. We believe these improvements should permit incorporation of mid-IR QCLs in reliable instrumentation. [reprint (PDF)]
10.	Wafer-scale epitaxial lift-off of optoelectronic grade GaN from a GaN substrate using a sacrificial ZnO interlayer Akhil Rajan, David J Rogers, Cuong Ton-That, Liangchen Zhu, Matthew R Phillips, Suresh Sundaram, Simon Gautier, Tarik Moudakir, Youssef El-Gmili, Abdallah Ougazzaden, Vinod E Sandana, Ferechteh H Teherani, Philippe Bove, Kevin A Prior, Zakaria Djebbour, Ryan McClintock and Manijeh Razeghi Journal of Physics D: Applied Physics, Volume 49, Number 31 -- July 15, 2016 ...[Visit Journal] Full 2 inch GaN epilayers were lifted off GaN and c-sapphire substrates by preferential chemical dissolution of sacrificial ZnO underlayers. Modification of the standard epitaxial lift-off (ELO) process by supporting the wax host with a glass substrate proved key in enabling full wafer scale-up. Scanning electron microscopy and x-ray diffraction confirmed that intact epitaxial GaN had been transferred to the glass host. Depth-resolved cathodoluminescence (CL) analysis of the bottom surface of the lifted-off GaN layer revealed strong near-band-edge (3.33 eV) emission indicating a superior optical quality for the GaN which was lifted off the GaN substrate. This modified ELO approach demonstrates that previous theories proposing that wax host curling was necessary to keep the ELO etch channel open do not apply to the GaN/ZnO system. The unprecedented full wafer transfer of epitaxial GaN to an alternative support by ELO offers the perspective of accelerating industrial adoption of the expensive GaN substrate through cost-reducing recycling. [reprint (PDF)]
10.	GaN-based nanostructured photodetectors J.L. Pau, C. Bayram, P. Giedraitis, R. McClintock, and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7222-14-- January 26, 2009 ...[Visit Journal] The use of nanostructures in semiconductor technology leads to the observation of new phenomena in device physics. Further quantum and non-quantum effects arise from the reduction of device dimension to a nanometric scale. In nanopillars, quantum confinement regime is only revealed when the lateral dimensions are lower than 50 nm. For larger mesoscopic systems, quantum effects are not observable but surface states play a key role and make the properties of nanostructured devices depart from those found in conventional devices. In this work, we present the fabrication of GaN nanostructured metal-semiconductor-metal (MSM) and p-i-n photodiodes (PIN PDs) by e-beam lithography, as well as the investigation of their photoelectrical properties at room temperature. The nanopillar height and diameter are about 520 nm and 200 nm, respectively. MSMs present dark currents densities of 0.4 A/cm² at ±100 V. A strong increase of the optical response with bias is observed, resulting in responsivities higher than 1 A/W. The relationship between this gain mechanism and surface states is discussed. PIN PDs yield peak responsivities (R_peak) of 35 mA/W at -4 V and show an abnormal increase of the response (R_peak > 100 A/W) under forward biases. [reprint (PDF)]
10.	High‐quality GaAs/Ga0.49In0.51P superlattices grown on GaAs and silicon substrates by low‐pressure metalorganic chemical vapor deposition Available M. Razeghi; Ph. Maurel; F. Omnes; M. Defour; C. Boothroyd; W. M. Stobbs; M. Kelly J. Appl. Phys. 63, 4511–4514 (1988) -- May 1, 1988 ...[Visit Journal] We report the successful growth of Ga0.49 Iuo.5 ! P-GaAs superlattices on GaAs and Si substrates by low-pressure metalorganic chemical vapor deposition. The high quality of the structure grown on GaAs and silicon substrates has been evidenced by transmission electron microscopy photographs, that show very sharp interfaces between GaAs wells and Gao.49InO.51 P barriers, with perfect control of thicknesses and compositions. Classical Hall measurements performed on the sample further demonstrated the presence of a twodimensional electron ga.<; with a mobility at T = 4 K , fL (4 K) = 50000 cm2 1V Is, and a carrier concentration n _ (4 K) = 2,9 X 1011 em -2. GaAs/Gao.49 InO. 51 P superlattices have been used, as well as buffer layer in order to grow GaAs on silicon substrates. Mirrorlike single-crystal GaAs has thus been obtained. A GaInP IGaAs heterostructure with electron HaH mobility as high as 6000 cm2 /V Is at 300 K and 80000 cm2 /V Is at 4 K has been grown, which is the highest mobility that has yet been reported for these materials, [reprint (PDF)]
10.	GaN p-i-n photodiodes with high visible-to-ultraviolet rejection ratio P. Kung, X. Zhang, D. Walker, A. Saxler, and M. Razeghi SPIE Conference, San Jose, CA, -- January 28, 1998 ...[Visit Journal] UV photodetectors are critical components in many applications, including UV astronomy, flame sensors, early missile threat warning and space-to-space communications. Because of the presence of strong IR radiation in these situations, the photodetectors have to be solar blind, i.e. able to detect UV radiation while not being sensitive to IR. Al_xGa_1-xN is a promising material system for such devices. Al_xGa_1-xN materials are wide bandgap semiconductors, with a direct bandgap whose corresponding wavelength can be continuously tuned from 200 to 365 nm. Al_xGa_1-xN materials are thus insensitive to visible and IR radiation whose wavelengths are higher than 365 nm. We have already reported the fabrication and characterization of Al_xGa_1-xN-based photoconductors with a cut-off wavelength tunable from 200 to 365 nm by adjusting the ternary alloy composition. Here, we present the growth and characterization of GaN p-i- n photodiodes which exhibit a visible-to-UV rejection ratio of 6 orders or magnitude. The thin films were grown by low pressure metalorganic chemical vapor deposition. Square mesa structures were fabricated using dry etching, followed by contact metallization. The spectral response, rejection ratio and transient response of these photodiodes is reported. [reprint (PDF)]
10.	Molecular Beam Epitaxial Growth of High Quality InSb for p-i-n Photodetectors G. Singh, E. Michel, C. Jelen, S. Slivken, J. Xu, P. Bove, I. Ferguson, and M. Razeghi Journal of Vacuum Science and Technology B, 13 (2)-- March 1, 1995 ...[Visit Journal] The InSb infrared photodetectors grown heteroepitaxially on Si substrates by molecular beam epitaxy (MBE) are reported. Excellent InSb material quality is obtained on 3-inch Si substrates (with a GaAs predeposition) as confirmed by structural, optical, and electrical analysis. InSb infrared photodetectors on Si substrates that can operate from 77 K to room temperature have been demonstrated. The peak voltage-responsitivity at 4 μm is about 1.0×10³ V/W and the corresponding Johnson-noise-limited detectivity is calculated to be 2.8×10¹⁰ cm·Hz^½/W. This is the first important stage in developing InSb detector arrays or monolithic focal plane arrays (FPAs) on silicon. The development of this technology could provide a challenge to traditional hybrid FPA's in the future. [reprint (PDF)]
10.	Radiometric characterization of long-wavelength infrared type II strained layer superlattice focal plane array under low-photon irradiance conditions J. Hubbs, V. Nathan, M. Tidrow, and M. Razeghi Optical Engineering, Vol. 51, No. 6, p. 064002-1-- June 15, 2012 ...[Visit Journal] We present the results of the radiometric characterization of an “M” structure long wavelength infrared Type-II strained layer superlattice(SLS) infrared focal plane array (IRFPA) developed by Northwestern University (NWU). The performance of the M-structure SLS IRFPA was radiometrically characterized as a function of photon irradiance, integration time, operating temperature, and detector bias. Its performance is described using standard figures of merit: responsivity, noise, and noise equivalent irradiance. Assuming background limited performance operation at higher irradiances, the detector quantum efficiency for the SLS detector array is approximately 57%. The detector dark density at 80 K is 142 μA∕cm², which represents a factor of seven reduction from previously measured devices. [reprint (PDF)]
10.	Effect of the spin split-off band on optical absorption in p-type Ga1 xInxAsyP1-y quantum-well infrared detectors J.R. Hoff, M. Razeghi and G. Brown Physical Review B 54 (15)-- October 15, 1996 ...[Visit Journal] Experimental investigations of p-type Ga_1-xIn_xAs_yP_1-y quantum-well intersubband photodetectors (QWIP’s) led to the discovery of unique features in photoresponse spectra of these devices. In particular, the strong 2–5 μm photoresponse of these QWIP’s was not anticipated based on previous experimental and theoretical results for p-type GaAs/Al_xGa_1-xAs QWIP’s. Our theoretical modeling of p-type QWIP’s based on the Ga_1-xIn_xAs_yP_1-y system revealed that the intense short-wavelength photoresponse was due to a much stronger coupling to the spin-orbit split-off components in the continuum than occurs for GaAs/Al_xGa_1-xAs QWIP’s. Due to the strong influence of the spin split-off band, an eight-band Kane Hamiltonian was required to accurately model the measured photoresponse spectra. This theoretical model is first applied to a standard p-type GaAs/Al_0.3Ga_0.7As QWIP, and then to a series of GaAs/Ga_0.51In_0.49P, GaAs/Ga_0.62In_0.38As_0.22P_0.78, Ga_0.79In_0.21As_0.59P_0.41/Ga_0.51In_0.49P, and Ga_0.79In_0.21As_0.59P_0.41/Ga_0.62In_0.38As_0.22P_0.78 QWIP’s. Through this analysis, the insignificance of spin split-off absorption in GaAs/Al_xGa_1-xAs QWIP’s is verified, as is the dual role of light-hole extended-state and spin split-off hole-extended-state absorption on the spectral shape of Ga_1-xIn_xAs_yP_1-y QWIP’s. [reprint (PDF)]
10.	High Detectivity InAs Quantum-Dot Infrared Photodetectors Grown on InP by Metalorganic Chemical Vapor Deposition W. Zhang, H. Lim, M. Taguchi, S. Tsao, B. Movaghar, and M. Razeghi Applied Physics Letters, 86 (19)-- May 9, 2005 ...[Visit Journal] We report a high-detectivity InAs quantum-dot infrared photodetector. The InAs quantum dots were grown by self-assembly on InP substrates via low-pressure metal–organic chemical–vapor deposition. Highly uniform quantum dots with a density of 4×10¹⁰ cm² were grown on a GaAs/InP matrix. Photoresponse was observed at temperatures up to 160 K with a peak of 6.4 µm and cutoff of 6.6 µm. Very low dark currents and noise currents were obtained by inserting Al_0.48In_0.52As current blocking layers. The background-limited performance temperature was 100 K. A detectivity of 1.0×10¹⁰ cm·Hz^½/W was obtained at 77 K with a bias of –1.1 V. [reprint (PDF)]

Page 24 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (736 Items)