Center for Quantum Devices - Most Downloaded Journal Articles

Page 22 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (738 Items)

13.	Gallium nitride on silicon for consumer & scalable photonics C. Bayram, K.T. Shiu, Y. Zhu, C.W. Cheng, D.K. Sadana, Z. Vashaei, E. Cicek, R. McClintock and M. Razeghi SPIE Proceedings, Vol. 8631, p. 863112-1, Photonics West, San Francisco, CA-- February 4, 2013 ...[Visit Journal] Gallium Nitride (GaN) is a unique material system that has been heavily exploited for photonic devices thanks to ultraviolet-to-terahertz spectral tunability. However, without a cost effective approach, GaN technology is limited to laboratory demonstrations and niche applications. In this investigation, integration of GaN on Silicon (100) substrates is attempted to enable widespread application of GaN based optoelectronics. Controlled local epitaxy of wurtzite phase GaN on on-axis Si(100) substrates is demonstrated via metal organic chemical vapor deposition (MOCVD). CMOS-compatible fabrication scheme is used to realize [SiO2-Si{111}-Si{100}] groove structures on conventional 200-mm Si(100) substrates. MOCVD growth (surface treatment, nucleation, initiation) conditions are studied to achieve controlled GaN epitaxy on such grooved Si(100) substrates. Scanning electron microscopy and transmission electron microscopy techniques are used to determine uniformity and defectivity of the GaN. Our results show that aforementioned groove structures along with optimized MOCVD growth conditions can be used to achieve controlled local epitaxy of wurtzite phase GaN on on-axis Si(100) substrates. [reprint (PDF)]
13.	LEO of III-Nitride on Al₂O₃ and Si Substrates M. Razeghi, P. Kung, P. Sandvik, K. Mi, X. Zhang, V.P. Dravid, J. Freitas, and A. Saxler SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] Lateral epitaxial overgrowth (LEO) has recently become the method of choice to reduce the density of dislocations in heteroepitaxial GaN thin films, and is thus expected to lead to enhanced performance devices. We present here the LEO growth and characterization of GaN films by low pressure metalorganic chemical vapor deposition. Various substrates were used, including basal plane sapphire and oriented Si substrates. The steps in the LEO growth technology will be briefly reviewed. The characterization results will be discussed in detail. The structural, electrical and optical properties of the films were assessed through scanning, atomic and transmission electron microscopy, x-ray diffraction, capacitance-voltage, deep level transient spectroscopy, photoluminescence, and scanning cathodoluminenscence measurements. Single-step and double- step LEO GaN was achieved on sapphire. Similarly high quality LEO grown GaN films were obtained on sapphire and silicon substrates. Clear and dramatic reduction in the density of defects are observed in LEO grown materials using the various characterization techniques mentioned previously. [reprint (PDF)]
13.	High-detectivity quantum-dot infrared photodetectors grown by metal-organic chemical-vapor deposition J. Szafraniec, S. Tsao, W. Zhang, H. Lim, M. Taguchi, A.A. Quivy, B. Movaghar and M. Razeghi Applied Physics Letters 88 (121102)-- March 20, 2006 ...[Visit Journal] A mid-wavelength infrared photodetector based on InGaAs quantum dots buried in an InGaP matrix and deposited on a GaAs substrate was demonstrated. Its photoresponse at T=77 K was measured to be around 4.7 μm with a cutoff at 5.5 μm. Due to the high peak responsivity of 1.2 A/W and low dark-current noise of the device, a specific peak detectivity of 1.1 x 10¹² cm·Hz^½·W⁻¹ was achieved at −0.9 V bias [reprint (PDF)]
13.	Characteristics of high quality p-type Al_xGa_1-xN/GaN superlattices A. Yasan, R. McClintock, S.R. Darvish, Z. Lin, K. Mi, P. Kung, and M. Razeghi Applied Physics Letters 80 (12)-- March 18, 2002 ...[Visit Journal] Very-high-quality p-type Al_xGa_1–xN/GaN superlattices have been grown by low-pressure metalorganic vapor-phase epitaxy through optimization of Mg flow and the period of the superlattice. For the superlattice with x = 26%, the hole concentration reaches a high value of 4.2×10¹⁸ cm^–3 with a resistivity as low as 0.19 Ω · cm by Hall measurement. Measurements confirm that superlattices with a larger period and higher Al composition have higher hole concentration and lower resistivity, as predicted by theory. [reprint (PDF)]
13.	Internal Stress Around Micropipes in 6H-SiC Substrates H. Ohsato, T. Kato, T. Okuda and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] 6H-SiC single crystals are expected to be suitable substrates for thin film growth of the wide bandgap semiconductor (GaN, because it has a small lattice mismatch with GaN. Moreover, SiC single crystals are also expected for high-power and high- temperature electric applications because of its wide band gap, high breakdown voltage, high thermal conductivity and high temperature stability. Single crystals with large size used for electronic devices can be grown on seed crystals only by the modified Lely method based on sublimation deposition. But, single crystals have serious defects so called micropipes. These micropipes penetrate almost along the [001] direction. The internal strain around micropipes was investigated using the polarizing optical microscope for the purpose of clarifying the formation mechanisms and decreasing the amount of micropipes. A special interference figure was found around a micropipe under the crossed polars on the polarizing microscope. In this work, the special interference figure around micropipes due to internal stress was explained, and the magnitude and distribution of the stress was measured by means of photoelasticity and the mapping of Raman spectra. [reprint (PDF)]
13.	Ridge-Width Dependence on High-Temperature Continuous-Wave Quantum-Cascade Laser Operation S. Slivken, J.S. Yu, A. Evans, L. Doris, J. David, and M. Razeghi IEEE Photonics Technology Letters, 16 (3)-- March 1, 2004 ...[Visit Journal] We report continuous-wave (CW) operation of quantum-cascade lasers (λ=6 μm) up to a temperature of 313 K (40°C). The maximum CW optical output powers range from 212 mW at 288 K to 22 mW at 313 K and are achieved with threshold current densities of 2.21 and 3.11 kA/cm2, respectively, for a high-reflectivity-coated 12-μm-wide and 2-mm-long laser. At room temperature (298 K), the power output is 145 mW at 0.87 A, corresponding to a power conversion efficiency of 1.68%. The maximum CW operating temperature of double-channel ridge waveguide lasers mounted epilayer-up on copper heatsinks is analyzed in terms of the ridge width, which is varied between 12 and 40 μm. A clear trend of improved performance is observed as the ridge narrows. [reprint (PDF)]
13.	High-Power Distributed-Feedback Quantum Cascade Lasers W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A.J. Evans, J.S. Yu, S.R. Darvish, S. Slivken and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 612704-- January 23, 2006 ...[Visit Journal] Recently, a distributed-feedback quantum cascade laser operating in a single spectral mode at 4.8 µm and at temperatures up to 333 K has been reported. In the present work, we provide detailed measurements and modeling of its performance characteristics. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single-mode at all currents and temperatures tested. Cw output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. [reprint (PDF)]
13.	Characterization of InTlSb/InSb Grown by Low Pressure Metalorganic Chemical Vapor Deposition on GaAs Substrat Y.H. Choi, P. Staveteig, E. Bigan, and M. Razeghi Journal of Applied Physics 75 (6)-- March 15, 1994 ...[Visit Journal] Optical properties of InTlSb, a new long wavelength infrared material, are investigated. InTlSb/InSb epilayers grown by low‐pressure metal‐organic chemical vapor deposition on semi‐insulating GaAs substrates were characterized using Auger electron spectroscopy and Fourier transform infrared spectroscopy. Auger electron spectra confirm the presence of thallium. Transmission measurements at 77 K indicate an absorption shift from 5.5 μm for InSb up to 8 μm for InTlSb that is confirmed by photoconductivity measurements. [reprint (PDF)]
13.	A review of the growth, doping, and applications of β-Ga₂O₃ thin films Manijeh Razeghi, Ji-Hyeon Park , Ryan McClintock, Dimitris Pavlidis, Ferechteh H. Teherani, David J. Rogers, Brenden A. Magill, Giti A. Khodaparast, Yaobin Xu, Jinsong Wu, Vinayak P. Dravid Proc. SPIE 10533, Oxide-based Materials and Devices IX, 105330R -- March 14, 2018 ...[Visit Journal] β-Ga₂O₃ is emerging as an interesting wide band gap semiconductor for solar blind photo detectors (SBPD) and high power field effect transistors (FET) because of its outstanding material properties including an extremely wide bandgap (Eg ~4.9eV) and a high breakdown field (8 MV/cm). This review summarizes recent trends and progress in the growth/doping of β-Ga₂O₃ thin films and then offers an overview of the state-of-the-art in SBPD and FET devices. The present challenges for β-Ga₂O₃ devices to penetrate the market in real-world applications are also considered, along with paths for future work. [reprint (PDF)]
13.	Photoconductance measurements on InTlSb/InSb/GaAs grown by low-pressure metalorganic chemical vapor deposition P.T. Staveteig, Y.H. Choi, G. Labeyrie, E. Bigan, and M. Razeghi Applied Physics Letters 64 (4)-- January 24, 1994 ...[Visit Journal] We report infrared photoconductors based on InTlSb/InSb grown by low‐pressure metalorganic chemical vapor deposition on semi-insulating GaAs substrates. The photoresponse spectrum extends up to 8 μm at 77 K. The absolute magnitude of the photoresponse is measured as a function of bias. The specific detectivity is estimated to be 3×10⁸ Hz^½·cm·W^-1 at 7 μm wavelength. [reprint (PDF)]
13.	Band gap tunability of Type-II Antimonide-based superlattices M. Razeghi and B.M. Nguyen Physics Procedia, Vol. 3, Issue 2, p. 1207-1212 (14th International Conference on Narrow Gap Semiconductors and Systems NGSS-14, Sendai, Japan, July 13-17, 2009)-- January 31, 2010 ...[Visit Journal] Current state-of-the art infrared photon detectors based on bulk semiconductors such as InSb or HgCdTe are now relatively mature and have almost attained the theoretical limit of performance. It means, however, that the technology can not be expected to demonstrate revolutionary improvements, in terms of device performances. In contrasts, low dimensional quantum systems such as superlattices, quantum wells, quantum dots, are still the development stage, yet have shown comparable performance to the bulk detector family. Especially for the Type-II Antimony-based superlattices, recent years have seen significant improvements in material quality, structural design as well as fabrication techniques which lift the performance of Type-II superlattice photodetectors to a new level. In this talk, we will discuss the advantages of Type-II-superlattices, from the physical nature of the material to the practical realisms. We will demonstrate the flexibility in controlling the energy gap and their overall band alignment for the suppression of Auger recombination, as well as to create sophisticated hetero-designs. [reprint (PDF)]
12.	Room temperature quantum cascade lasers with 27% wall plug efficiency Y. Bai, N. Bandyopadhyay, S. Tsao, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 98, No. 18, p. 181102-1-- May 3, 2011 ...[Visit Journal] Using the recently proposed shallow-well design, we demonstrate InP based quantum cascade lasers (QCLs) emitting around 4.9 μm with 27% and 21% wall plug efficiencies in room temperature (298 K) pulsed and continuous wave (CW) operations, respectively. The laser core consists of 40 QCL-stages. The highest cw efficiency is obtained from a buried-ridge device with a ridge width of 8 μm and a cavity length of 5 mm. The front and back facets are antireflection and high-reflection coated, respectively. The maximum single facet cw power at room temperature amounts to 5.1 W. [reprint (PDF)]
12.	High Performance Planar Antimony-Based Superlattice Photodetectors Using Zinc Diffusion Grown by MBE Jiakai Li, R. K. Saroj, Steven Slivken, V. H. Nguyen, Gail Brown and Manijeh Razeghi Photonics 2022, 9, 664 ...[Visit Journal] In this letter, we report a mid-wavelength infrared (MWIR) planar photodetector based on InAs/InAsSb type-II superlattices (T2SLs) that has a cut-off wavelength of 4.3 um at 77 K. The superlattice for the device was grown by molecular beam epitaxy while the planar device structure was achieved by Zinc diffusion process in a metal–organic chemical vapor deposition reactor. At 77 K, the peak responsivity and the corresponding quantum efficiency had the value of 1.42 A/W and 48% respectively at 3.7 um under -20 mV for the MWIR planar photodetector. At 77 K, the MWIR planar photodetector exhibits a dark current density of 2.0E5 A/cm^2 and the R0A value of ~3.0E2 Ohm cm^2 under -20 mV, which yielded a specific detectivity of 4.0E11 cm Hz^(1/2)/W at 3.7 um. At 150 K, the planar device showed a dark current density of 6.4E-5 A/cm^2 and a quantum efficiency of 49% at ~3.7 um under -20 mV, which yielded a specific detectivity of 2.0E11 cm Hz^(1/2)/W. [reprint (PDF)]
12.	Suppression of surface leakage in gate controlled type-II InAs/GaSb mid-infrared photodetectors G. Chen; B.-M. Nguyen; A.M. Hoang; E.K. Huang; S.R. Darvish; M. Razeghi Proc. SPIE 8268, Quantum Sensing and Nanophotonic Devices IX, 826811 (January 20, 2012)-- January 20, 2012 ...[Visit Journal] One of the biggest challenges of improving the electrical performance in Type II InAs/GaSb superlattice photodetector is suppressing the surface leakage. Surface leakage screens important bulk dark current mechanisms, and brings difficulty and uncertainty to the material optimization and bulk intrinsic parameters extraction such as carrier lifetime and mobility. Most of surface treatments were attempted beyond the mid-infrared (MWIR) regime because compared to the bulk performance, surface leakage in MWIR was generally considered to be a minor factor. In this work, we show that below 150K, surface leakage still strongly affects the electrical performance of the very high bulk performance p-π-M-n MWIR photon detectors. With gating technique, we can effectively eliminate the surface leakage in a controllable manner. At 110K, the dark current density of a 4.7 μm cut-off gated photon diode is more than 2 orders of magnitude lower than the current density in SiO₂ passivated ungated diode. With a quantum efficiency of 48%, the specific detecivity of gated diodes attains 2.5 x 10¹⁴ cm·Hz^1/2/W, which is 3.6 times higher than that of ungated diodes. [reprint (PDF)]
12.	On the interface properties of ZnO/Si electroluminescent diodes J.L. Pau, J. Piqueras, D.J. Rogers, F. Hosseini Teherani, K. Minder, R. McClintock, and M. Razeghi Journal of Applied Physics, Vol. 107, No. 3, p. 033719-1-- February 1, 2010 ...[Visit Journal] ZnO layers grown on n⁻–Si(100), n⁺–Si(100), and n^––Si(111) substrates by pulsed-laser deposition were found to give electroluminescence. Light emission was observed in the form of discrete spots for currents over 1 mA with a white appearance to the naked eye. The intensity of these spots showed an erratic behavior over time, appearing and disappearing at random, while showing an associated random telegraph noise in the current signal. Regardless the substrate used, the electroluminescence spectra had a main broadband emission centered at about 600 nm and a relatively small peak at around 380 nm which corresponds to the energy of ZnO near band edge emission. Furthermore, the devices exhibited rectifying characteristics, whose current blocking direction depended on the substrate orientation. Optimization of ZnO conductivity and performing sample growth in N₂ ambient were found to be critical to enhance the emission intensity. Rutherford backscattering characterization revealed the existence of an intermixed region at the interface between ZnO and Si. To study the electronic properties at the interface, frequency dependent capacitance measurements were carried out. The junction capacitance became frequency dependent at the bias voltages at which light emission occurs due to the relatively slow trapping and generation processes at deep centers. These centers are believed to play an important role in the mechanism of light emission. [reprint (PDF)]
12.	Quantum oscillations at a Ga0.47In0.53AsInP heterojunction interface R.J Nicholas a, M.A Brummell a , J.C Portal b, M Razeghi c, M.A Poisson R.J Nicholas, M.A Brummell, J.C Portal, M Razeghi, M.A Poisson, Quantum oscillations at a Ga0.47In0.53AsInP heterojunction interface, Solid State Communications, Volume 43, Issue 11, 1982, Pages 825-828,-- September 1, 1982 ...[Visit Journal] We report the observation of a two dimensional gas of high mobility electrons at the interface of a Ga0.47In0.53AsInP heterojunction grown by MOCVD. The two dimensional electron concentrations and effective mass are determined by Shubnikov-de Haas studies, and compared with theoretical predictions. Evidence of an enhancement of the g-factor is observed. We also report observations of very pronounced quantum Hall steps as seen in GaAs-GaAlAs heterojunctions. [reprint (PDF)]
12.	Frequency-Shifted Polaron Coupling in Ga0.47In0.53As Heterojunctions R. J. Nicholas, L. C. Brunel, S. Huant, K. Karrai, and J. C. Portal† M. A. Brummell M. Razeghi K. Y. Cheng and A. Y. Cho Phys. Rev. Lett. 55, 883 – 1985-- August 19, 1985* ...[Visit Journal] Frequency-dependent cyclotron-resonance measurements are reported on Ga0.47In0.53As-InP and Ga0.47In0.53A⁢s−A⁢l0.48In0.52As heterojunctions. Discontinuities in the effective mass occur at two frequencies as a result of resonant polaron coupling with both optic-phonon modes present in the Ga0.47In0.53As alloy. The coupling occurs at the frequencies at the TO phonons, in contrast to measurements on bulk materials. Possible changes in the screening and polarization of the optic-phonon modes are considered. [reprint (PDF)]
12.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, P. Sung, S.R. Darvish, W. Zhang, A. Evans, S. Slivken, and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 69000A-1-8.-- February 1, 2008 ...[Visit Journal] We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~ 4.75 µm. Ridge waveguides of 50 µm and 100 µm width were fabricated with both PCDFB and Fabry-Perot feedback mechanisms. The Fabry-Perot device has a broad emitting spectrum and a broad far-field character. The PCDFB devices have primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half-maximum of 4.8 degrees and 2.4 degrees for the 50 µm and 100 µm ridge widths, respectively. [reprint (PDF)]
12.	Growth and Characterization of Type-II Non-Equilibrium Photovoltaic Detectors for Long Wavelength Infrared Range H. Mohseni, J. Wojkowski, A. Tahraoui, M. Razeghi, G. Brown and W. Mitche SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] Growth and characterization of type-II detectors for mid-IR wavelength range is presented. The device has a p-i-n structure is designed to operate in the non-equilibrium mode with low tunneling current. The active layer is a short period InAs/GaSb superlattice. Wider bandgap p-type AlSb and n-type InAs layers are used to facilitate the extraction of both electronics and holes from the active layer for the first time. The performance of these devices were compared to the performance of devices grown at the same condition, but without the AlSb barrier layers. The processed devices with the AlSb barrier show a peak responsivity of about 1.2 A/W with Johnson noise limited detectivity of 1.1 X 10¹¹ cm·Hz^½/W at 8 μm at 80 K at zero bias. The details of the modeling, growth, and characterizations will be presented. [reprint (PDF)]
12.	Roadmap of Semiconductor Infrared Lasers and Detectors for the 21st Century M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] Since the first discovery, semiconductor infrared lasers and detectors have found many various applications in military, communications, medical, and industry sections. In this paper, the current status of semiconductor infrared lasers and detectors will be reviewed. Advantages and disadvantages of different methods and techniques is discussed later. Some basic physical limitations of current technology are studied and the direction to overcome these problems will be suggested. [reprint (PDF)]
12.	Metalorganic chemical vapor deposition of monocrystalline GaN thin films on β-LiGaO2substrates P. Kung, A. Saxler, X. Zhang, D. Walker, R. Lavado, and M. Razeghi Applied Physics Letters 69 (14)-- September 30, 1996 ...[Visit Journal] We report the metalorganic chemical vapor deposition growth and characterization of monocrystalline GaN thin films on β-LiGaO₂ substrates. The influence of the growth temperature on the crystal quality was studied. The structural, electrical, and optical properties of the films were assessed through scanning electron microscopy, x-ray diffraction, Hall measurements, optical transmission, photoluminescence. [reprint (PDF)]
12.	Phase-matched optical second-harmonic generation in GaN and AlN slab waveguides D.N. Hahn, G.T. Kiehne, G.K.L. Wong, J.B. Ketterson, P. Kung, A. Saxler and M. Razeghi Journal of Applied Physics 85 (5)-- March 1, 1999 ...[Visit Journal] Phase-matched optical second-harmonic (SH) generation was observed in GaN and AlN slab waveguides. Phase matching was achieved by waveguide modal dispersion. By tuning the output wavelength of an optical parametric amplifier, several phased-matched SH peaks were observed in the visible spectrum covering blue to red wavelengths. The peak positions are in agreement with the values calculated using the dispersive refractive indices of the film and substrate materials. [reprint (PDF)]
12.	Shortwave quantum cascade laser frequency comb for multi-heterodyne spectroscopy Q. Y. Lu, S. Manna, D. H. Wu, S. Slivken, and M. Razeghi Applied Physics Letters 112, 141104-- April 3, 2018 ...[Visit Journal] Quantum cascade lasers (QCLs) are versatile light sources with tailorable emitting wavelengths covering the mid-infrared and terahertz spectral ranges. When the dispersion is minimized, frequency combs can be directly emitted from quantum cascade lasers via four-wave mixing. To date, most of the mid-infrared quantum cascade laser combs are operational in a narrow wavelength range wherein the QCL dispersion is minimal. In this work, we address the issue of very high dispersion for shortwave QCLs and demonstrate 1-W dispersion compensated shortwave QCL frequency combs at λ~5.0 μm, spanning a spectral range of 100 cm⁻¹. The multi-heterodyne spectrum exhibits 95 equally spaced frequency comb lines, indicating that the shortwave QCL combs are ideal candidates for high-speed high-resolution spectroscopy [reprint (PDF)]
12.	High Performance Quantum Cascade Laser Results at the Centre for Quantum Devices M. Razeghi and S. Slivken Physica Status Solidi, 195 (1)-- January 1, 2003 ...[Visit Journal] In this paper, we review some of the history and recent results related to the development of the quantum cascade laser at the Center for Quantum Devices. The fabrication of the quantum cascade laser is described relative to growth, characterization, and processing. State-of-the-art testing results for 5-11 μm lasers will be then be explored, followed by a future outlook for the technology. [reprint (PDF)]
12.	Metalorganic chemical vapor deposition of undoped In1−xAlxAs on InP M. A. di Forte‐Poisson; M. Razeghi; J. P. Duchemin M. A. di Forte‐Poisson, M. Razeghi, J. P. Duchemin; Metalorganic chemical vapor deposition of undoped In1−xAlxAs on InP. J. Appl. Phys. 1 December 1983; 54 (12): 7187–7189. https://doi.org/10.1063/1.331956-- December 1, 1983 ...[Visit Journal] In1−x Alx As epitaxial layers were grown on (100) InP substrates by the organometallic vapor phase epitaxy method. Undoped layers with mirror smooth surfaces were obtained for substrate temperatures of 600–650 °C. By adjusting the relative ratio of In and Al, lattice matched In0.52 Al0.48 As epilayers were reproducibly grown on InP substrates. X‐ray measurements, scanning Auger analyses, and electron mobilities are presented. These results show that the quality of the epilayers obtained here was comparable to the best reported layers grown by other methods. [reprint (PDF)]

Page 22 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (738 Items)