Center for Quantum Devices - Most Downloaded Journal Articles

Page 2 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)

19.	High performance InAs quantum dot infrared photodetectors (QDIP) on InP by MOCVD W. Zhang, H. Lim, M. Taguchi, S. Tsao, J. Szafraniec, B. Movaghar, M. Razeghi, and M. Tidrow SPIE Conference, Jose, CA, Vol. 5732, pp. 326-- January 22, 2005 ...[Visit Journal] Inter-subband detectors such as quantum well infrared photodetectors (QWIP) have been widely used in infrared detection. Quantum dot infrared photodetectors (QDIPs) have been predicted to have better performance than QWIPs including higher operation temperature and normal incidence detection. Here we report our recent results of InAs QDIP grown on InP substrate by low-pressure metalorganic chemical vapor deposition (MOCVD). The device structures consist of multiple stacks of InAs quantum dots with InP barriers. High detectivities in the range of 10¹⁰cm·Hz^1/2/W were obtained at 77K. The measurements at higher temperatures show better temperature dependent performance than QWIP. However, the performances of QDIPs are still far from the expected. One of the reasons is the low quantum efficiency due to the low fill factor of quantum dots layer. Resonant cavity enhanced QDIP has been studied to increase the quantum efficiency. Different schemes of mirrors using free carrier plasma and distributed Bragg reflector are discussed. [reprint (PDF)]
19.	Multiple-band, Single-mode, High-power, Phase-locked, Mid-infrared Quantum Cascade Laser Arrays Manijeh Razeghi, Wenjia Zhou, Quanyong Lu, Donghai Wu, and Steven Slivken Imaging and Applied Optics 2018, JTh1A.2-- September 15, 2018 ...[Visit Journal] Single-mode, 16-channel, phase-locked laser arrays based on quantum cascade laser technology are demonstrated at multiple spectral bands across the mid-infrared spectrum region. High peak output power of 50W is achieved around the long-wavelength band of 7.7µm, while a side mode suppression ratio over 25dB is obtained. Far field distribution measurement result indicates a uniform phase distribution across the array output. [reprint (PDF)]
19.	Aluminum-free Quantum Well Intersubband Photodetectors with p-type GaAs Wells and lattice-matched ternary and quaternary barriers J. Hoff, E. Bigan, G.J. Brown, and M. Razeghi Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995 ...[Visit Journal] Acceptor doped Quantum Well Intersubband Photodetectors with GaAs wells and lattice matched barriers of both ternary (In_0.49Ga_0.51P) and quaternary (In_0.62Ga_0.38As_0.22P_0.78) materials have been grown on semi-insulating GaAs substrates by Low Pressure Metal Organic Chemical Vapor Deposition. Mesa devices were fabricated and subjected to a series of tests to illuminate experimentally some of the detection capabilities of the lattice matched quaternary InxGa1-xAsyP1-y system with (0 ≤ x ≤ 0.52) and (0 ≤ y ≤ 1). The observed photoresponse cut-off wavelengths are in good agreement with the activation energies observed in the temperature dependence of the dark currents. Kronig-Penney calculations were used to model the intersubband transition energies. [reprint (PDF)]
19.	Room temperature quantum cascade laser with ∼ 31% wall-plug efficiency F. Wang, S. Slivken, D. H. Wu, and M. Razeghi AIP Advances 10, 075012-- July 14, 2020 ...[Visit Journal] In this article, we report the demonstration of a quantum cascade laser emitting at λ ≈ 4.9 μm with a wall-plug efficiency of ∼31% and an output power of ∼23 W in pulsed operation at room temperature with 50 cascade stages (Ns). With proper fabrication and packaging, this buried ridge quantum cascade laser with a cavity length of 5 mm delivers more than ∼15 W output power, and its wall-plug efficiency exceeds ∼20% at 100 °C. The experimental results of the lasers are well in agreement with the numerical predictions. [reprint (PDF)]
19.	Solar-blind avalanche photodiodes R. McClintock, K. Minder, A. Yasan, C. Bayram, F. Fuchs, P. Kung and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 61271D-- January 23, 2006 ...[Visit Journal] There is a need for semiconductor based UV photodetectors to support avalanche gain in order to realize better performance and more effectively compete with existing photomultiplier tubes. However, there are numerous technical issues associated with the realization of high-quality solar-blind avalanche photodiodes (APDs). In this paper, APDs operating at 280 nm, within the solar-blind region of the ultraviolet spectrum, are investigated. [reprint (PDF)]
19.	Direct growth of thick AlN layers on nanopatterned Si substrates by cantilever epitaxy Ilkay Demir, Yoann Robin, Ryan McClintock, Sezai Elagoz, Konstantinos Zekentes, and Manijeh Razeghi Physica Status Solidi 214 (4), pp. 1770120-- April 4, 2017 ...[Visit Journal] The growth of thick, high quality, and low stress AlN films on Si substrates is highly desired for a number of applications like the development of micro and nano electromechanical system (MEMS and NEMS) technologies [1] and particularly for fabricating AlGaNbased UV LEDs [2–5]. UV LEDs are attractive as they are applied in many areas, such as biomedical instrumentations and dermatology, curing of industrial resins and inks, air purification, water sterilization, and many others [2, 3]. UV LEDs have been generally fabricated on AlN, GaN, Al₂O₃, or SiC substrates because of better lattice mismatching to AlGaN material systems. [reprint (PDF)]
19.	High power continuous wave operation of single mode quantum cascade lasers up to 5 W spanning λ∼3.8-8.3 µm Quanyong Lu, Steven Slivken, Donghai Wu, and Manijeh Razeghi Optics Express Vol. 28, Issue 10, pp. 15181-15188-- May 4, 2020 ...[Visit Journal] In this work, we report high power continuous wave room-temperature operation single mode quantum cascade lasers in the mid-infrared spectral range from 3.8 to 8.3 µm. Single mode robustness and dynamic range are enhanced by optimizing the distributed feedback grating coupling design and the facet coatings. High power single mode operation is secured by circumventing the over-coupling issue and spatial hole burning effect. Maximum single-facet continuous-wave output power of 5.1 W and wall plug efficiency of 16.6% is achieved at room temperature. Single mode operation with a side mode suppression ratio of 30 dB and single-lobed far field with negligible beam steering is observed. The significantly increased power for single mode emission will boost the QCL applications in long-range free-space communication and remote sensing of hazardous chemicals. [reprint (PDF)]
18.	Materials characterization of n-ZnO/p-GaN:Mg/c-Al(2)O(3) UV LEDs grown by pulsed laser deposition and metal-organic chemical vapor deposition D. Rogers, F.H. Teherani, P. Kung, K. Minder, and M. Razeghi Superlattices and Microstructures-- April 1, 2007 ...[Visit Journal] n-ZnO/p-GaN:Mg hybrid heterojunctions grown on c-Al₂O₃ substrates showed 375 nm room temperature electroluminescence. It was suggested that the high materials and interface quality obtained using pulsed laser deposition for the n-ZnO growth and metal–organic chemical vapor deposition for the p-GaN:Mg were key factors enabling the injection of holes and the radiative near band edge recombination in the ZnO. In this paper we present the materials characterization of this structure using x-ray diffraction, scanning electron microscopy and atomic force microscopy. [reprint (PDF)]
18.	Aluminum free GaInP/GaAs Quantum Well Infrared Photodetectors for Long Wavelength Detection C. Jelen, S. Slivken, J. Hoff, M. Razeghi, and G. Brown Applied Physics Letters 70 (3)-- January 20, 1997 ...[Visit Journal] We demonstrate quantum well infrared photodetectors based on a GaAs/Ga_0.51In_0.49P superlattice structure grown by gas-source molecular beam epitaxy. Wafers were grown with varying well widths. Wells of 40, 65, and 75 Å resulted in peak detection wavelengths of 10.4, 12.8, and 13.3 μm with a cutoff wavelength of 13.5, 15, and 15.5 μm, respectively. The measured peak and cutoff wavelengths match those predicted by eight band theoretical analysis. Measured dark currents were lower than equivalent GaAs/AlGaAs samples. [reprint (PDF)]
18.	Toward realization of small-size dual-band long-wavelength infrared photodetectors based on InAs/GaSb/AlSb type-II superlattices Romain Chevallier, Abbas Haddadi, Manijeh Razeghi Solid-State Electronics 136, pp. 51-54-- June 20, 2017 ...[Visit Journal] In this study, we demonstrate 12 × 12 µm² high-performance, dual-band, long-wavelength infrared (LWIR) photodetectors based on InAs/GaSb/AlSb type-II superlattices. The structure consists of two back-to-back heterojunction photodiodes with 2 µm-thick p-doped absorption regions. High quality dry etching combined with SiO₂ passivation results in a surface resistivity value of 7.9 × 10⁵ Ω·cm for the longer (red) channel and little degradation of the electrical performance. The device reaches dark current density values of 4.5 × 10⁻⁴ A/cm² for the longer (red) and 1.3 × 10⁻⁴ A/cm² for the shorter (blue) LWIR channels at quantum efficiency saturation. It has 50% cut-off wavelengths of 8.3 and 11.2 µm for the blue and red channel, respectively, at 77 K in back-side illumination configuration and exhibits quantum efficiencies of 37% and 29%, respectively. This results in specific detectivity values of 2.5 × 10¹¹ cm·Hz^½/W and 1.3 × 10¹¹ cm·Hz^½/W at 77 K. [reprint (PDF)]
18.	Positive and negative luminescence in binary Type-II InAs/GaSb superlattice photodiodes D. Hoffman and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 61271H-- January 23, 2006 ...[Visit Journal] In the present work, we show measurements of both positive and negative luminescence of binary Type-II InAs/GaSb superlattice photodiodes in the 3 to 13 μm spectral range. Through a radiometric calibration technique, we demonstrate temperature independent negative luminescence efficiencies of 45 % in the midwavelength (MWIR) sample from 220 K to 320 K without anti-reflective coating and values reaching 35 % in the long wavelength infrared (LWIR) spectrum sample. [reprint (PDF)]
18.	High efficiency quantum cascade laser frequency comb Quanyong Lu, Donghai Wu, Steven Slivken & Manijeh Razeghi Scientific Reports 7, Article number: 43806-- March 6, 2017 ...[Visit Journal] An efficient mid-infrared frequency comb source is of great interest to high speed, high resolution spectroscopy and metrology. Here we demonstrate a mid-IR quantum cascade laser frequency comb with a high power output and narrow beatnote linewidth at room temperature. The active region was designed with a strong-coupling between the injector and the upper lasing level for high internal quantum efficiency and a broadband gain. The group velocity dispersion was engineered for efficient, broadband mode-locking via four wave mixing. The comb device exhibits a narrow intermode beatnote linewidth of 50.5 Hz and a maximum wall-plug efficiency of 6.5% covering a spectral coverage of 110 cm⁻¹ at λ ~ 8 μm. The efficiency is improved by a factor of 6 compared with previous demonstrations. The high power efficiency and narrow beatnote linewidth will greatly expand the applications of quantum cascade laser frequency combs including high-precision remote sensing and spectroscopy. [reprint (PDF)]
18.	Anomalous Hall Effect in InSb Layers Grown by MOCVD on GaAs Substrates C. Besikci, Y.H. Choi, R. Sudharsanan, and M. Razeghi Journal of Applied Physics 73 (10)-- May 15, 1993 ...[Visit Journal] InSb epitaxial layers have been grown on GaAs substrates by low‐pressure metalorganic chemical vapor deposition. A 3.15 μm thick film yielded an x‐ray full width at half maximum of 171 arcsec. A Hall mobility of 76 200 cm²/V· s at 240 K and a full width at half maximum of 174 arcsec have been measured for a 4.85 μm thick epilayer. Measured Hall data have shown anomalous behavior. A decrease in Hall mobility with decreasing temperature has been observed and room‐temperature Hall mobility has increased with thickness. In order to explain the anomalous Hall data, and the thickness dependence of the measured parameters, the Hall coefficient and Hall mobility have been simulated using a three‐layer model including a surface layer, a bulklike layer, and an interface layer with a high density of defects. Theoretical analysis has shown that anomalous behavior can be attributed to donor-like defects caused by the large lattice mismatch and to a surface layer which dominates the transport in the material at low temperatures. [reprint (PDF)]
18.	Growth and characterization of InGaAs/InGaP quantum dots for mid-infrared photoconductive detector S. Kim, H. Mohseni, M. Erdtmann, E. Michel, C. Jelen and M. Razeghi Applied Physics Letters 73 (7)-- August 17, 1998 ...[Visit Journal] We report InGaAs quantum dot intersubband infrared photodetectors grown by low-pressure metalorganic chemical vapor deposition on semi-insulating GaAs substrates. The optimum growth conditions were studied to obtain uniform InGaAs quantum dots constructed in an InGaP matrix. Normal incidence photoconductivity was observed at a peak wavelength of 5.5 μm with a high responsivity of 130 mA/W and a detectivity of 4.74×10⁷ cm· Hz^½/W at 77 K. [reprint (PDF)]
18.	Bias–selectable nBn dual–band long–/very long–wavelength infrared photodetectors based on InAs/InAsSb/AlAsSb type–II superlattices Abbas Haddadi, Arash Dehzangi, Romain Chevallier, Sourav Adhikary, & Manijeh Razeghi Nature Scientific Reports 7, Article number: 3379-- June 13, 2017 ...[Visit Journal] Type–II superlattices (T2SLs) are a class of artificial semiconductors that have demonstrated themselves as a viable candidate to compete with the state–of–the–art mercury–cadmium–telluride material system in the field of infrared detection and imaging. Within type–II superlattices, InAs/InAs_1−xSb_x T2SLs have been shown to have a significantly longer minority carrier lifetime. However, demonstration of high–performance dual–band photodetectors based on InAs/InAs_1−xSb_x T2SLs in the long and very long wavelength infrared (LWIR & VLWIR) regimes remains challenging. We report the demonstration of high–performance bias–selectable dual–band long–wavelength infrared photodetectors based on new InAs/InAsSb/AlAsSb type–II superlattice design. Our design uses two different bandgap absorption regions separated by an electron barrier that blocks the transport of majority carriers to reduce the dark current density of the device. As the applied bias is varied, the device exhibits well–defined cut–off wavelengths of either ∼8.7 or ∼12.5 μm at 77 K. This bias–selectable dual–band photodetector is compact, with no moving parts, and will open new opportunities for multi–spectral LWIR and VLWIR imaging and detection. [reprint (PDF)]
18.	Continuous wave quantum cascade lasers with 5.6 W output power at room temperature and 41% wall-plug efficiency in cryogenic operation F. Wang, S. Slivken, D. H. Wu, Q. Y. Lu, and M. Razeghi AIP Advances 10, 055120-- May 19, 2020 ...[Visit Journal] In this paper, we report a post-polishing technique to achieve nearly complete surface planarization for the buried ridge regrowth processing of quantum cascade lasers. The planarized device geometry improves the thermal conduction and reliability and, most importantly, enhances the power and efficiency in continuous wave operation. With this technique, we demonstrate a high continuous wave wall-plug efficiency of an InP-based quantum cascade laser reaching ∼41% with an output power of ∼12 W from a single facet operating at liquid nitrogen temperature. At room temperature, the continuous wave output power exceeds the previous record, reaching ∼5.6 W. [reprint (PDF)]
18.	Recent Advances in InAs/GaSb Superlattices for Very Long Wavelength Infrared Detection G.J. Brown, F. Szmulowicz, K. Mahalingam, S. Houston, Y. Wei, A. Gin and M. Razeghi SPIE Conference, San Jose, CA, Vol. 4999, pp. 457-- January 27, 2003 ...[Visit Journal] New infrared (IR) detector materials with high sensitivity, multi-spectral capability, improved uniformity and lower manufacturing costs are required for numerous long and very long wavelength infrared imaging applications. One materials system has shown great theoretical and, more recently, experimental promise for these applications: InAs/In_xGa_1-xSb type-II superlattices. In the past few years, excellent results have been obtained on photoconductive and photodiode samples designed for infrared detection beyond 15 microns. The infrared properties of various compositions and designs of these type-II superlattices have been studied. The infrared photoresponse spectra are combined with quantum mechanical modeling of predicted absorption spectra to provide insight into the underlying physics behind the quantum sensing in these materials. Results for superlattice photodiodes with cut-off wavelengths as long as 25 microns are presented. [reprint (PDF)]
18.	Sb-based infrared materials and photodetectors for the near room temperature applications J.D. Kim, E. Michel, H. Mohseni, J. Wojkowski, J.J. Lee and M. Razeghi SPIE Conference, San Jose, CA, Vol. 2999, pp. 55-- February 12, 1997 ...[Visit Journal] We report on the growth of InSb, InAsSb, and InTlSb alloys for infrared photodetector applications. The fabrication and characterization of photodetectors based on these materials are also reported. Both photoconductive and photovoltaic devices are investigated. The materials and detector structures were grown on (100) and (111)B semi-insulating GaAs and GaAs coated Si substrates by low pressure metalorganic chemical vapor deposition and solid source molecular beam epitaxy. Photoconductive detectors fabricated from InAsSb and InTlSb have been operated in the temperature range from 77 K to 300 K. The material parameters for photovoltaic device structures have been optimized through theoretical calculations based on fundamental mechanisms. InSb p-i-n photodiodes with 77 K peak responsivities approximately 103 V/W were grown on Si and (111) GaAs substrates. An InAsSb photovoltaic detector with a composition of x equals 0.85 showed photoresponse up to 13 micrometers at 300 K with a peak responsivity of 9.13 X 10-2 V/W at 8 micrometers . The RoA product of InAsSb detectors has been theoretically and experimentally analyzed. [reprint (PDF)]
18.	Solar blind GaN p-i-n photodiodes D. Walker, A. Saxler, P. Kung, X. Zhang, M. Hamilton, J. Diaz and M. Razeghi Applied Physics Letters 72 (25)-- June 22, 1998 ...[Visit Journal] We present the growth and characterization of GaN p-i-n photodiodes with a very high degree of visible blindness. The thin films were grown by low-pressure metalorganic chemical vapor deposition. The room-temperature spectral response shows a high responsivity of 0.15 A/W up until 365 nm, above which the response decreases by six orders of magnitude. Current/voltage measurements supply us with a zero bias resistance of 10¹¹ Ω. Lastly, the temporal response shows a rise and fall time of 2.5 μs measured at zero bias. This response time is limited by the measurement circuit. [reprint (PDF)]
18.	Nickel oxide growth on Si (111), c-Al₂O₃ and FTO/glass by pulsed laser deposition V. E. Sandana ; D. J. Rogers ; F. Hosseini Teherani ; P. Bove ; R. McClintock ; M. Razeghi 03/07/2014-- March 7, 2014 ...[Visit Journal] NiO was grown on Si (111), c-Al₂O₃ and FTO/glass substrates by pulsed laser deposition (PLD). X-Ray Diffraction (XRD) and scanning electron microscope (SEM) studies revealed that layers grown on c-Al₂O₃ were fcc NiO with a dense morphology of cubic grains that were strongly (111) oriented along the growth direction. The relatively low ω rocking curve linewidth, of 0.12°suggests that there may have been epitaxial growth on the c-Al₂O₃ substrate. XRD and SEM indicated that films grown on Si (111) were also fcc NiO, with cubic grains, but that the grain orientation was random. This is consistent with the presence of an amorphous SiO₂ layer at the surface of the Si substrate, which precluded epitaxial growth. NiO grown at lower temperature (200°C) on temperature-sensitive FTO/glass substrates showed no evidence of crystallinity in XRD and SEM studies. After flash annealing in air, however, peaks characteristic of randomly oriented fcc NiO appeared in the XRD scans and the surface morphology became more granular in appearance. Such layers appear promising for the development of future dye-sensitised solar cell devices based on NiO grown by PLD. [reprint (PDF)]
17.	Solar-Blind Deep UV Avalanche Photodetectors Using Reduced Area Epitaxy Lakshay Gautam , Junhee Lee, Michael Richards, and Manijeh Razeghi , Lakshay Gautam, Manijeh Razeghi, IEEE JOURNAL OF QUANTUM ELECTRONICS, VOL. 59, NO. 6, 10.1109/JQE.2023.3325254 ...[Visit Journal] We report high gain avalanche photodetectors operating in the deep UV wavelength regime. The high gain was leveraged through reduced area epitaxy by patterning AlN on Sapphire substrate. This helps in a substantial reduction of crack formation due to overgrowth on individually isolated AlN mesas. Reproducible gain on the order of 105 was reported for multiple diodes in different areas of 320 × 256 focal plane array. [reprint (PDF)]
17.	Imprinting of Nanoporosity in Lithium-Doped Nickel Oxide through the use of Sacrificial Zinc Oxide Nanotemplates Vinod E. Sandana, David J. Rogers, Ferechteh H. Teheran1, Philippe Bove, Ryan McClintock and Manijeh Razeghi Proc. SPIE 10105, Oxide-based Materials and Devices VIII, 101052C-- April 3, 2017 ...[Visit Journal] Methods for simultaneously increasing the conductivity and the porosity of NiO layers grown by pulsed laser deposition (PLD) were investigated in order to develop improved photocathodes for p-DSSC applications. NiO:Li (20at%) layers grown on c-Al₂O₃ by PLD showed a sharp drop in conductivity with increasing substrate temperature. Layers grown at room temperature were more than two orders of magnitude more conductive than undoped NiO layers but did not show evidence of any porosity in Scanning Electron Microscope (SEM) images. A new method for imposing a nanoporosity in NiO was developed based on a sacrificial template of nanostructured ZnO. SEM images and EDX spectroscopy showed that a nanoporous morphology had been imprinted in the NiO overlayer after preferential chemical etching away of the nanostructured ZnO underlayer. Beyond p-DSSC applications, this new process could represent a new paradigm for imprinting porosity in a whole range of materials. [reprint (PDF)]
17.	Novel Method for Reclaim/Reuse of Bulk GaN Substrates using Sacrifical ZnO Release Layers A. Rajan, S. Sundaram, Y. El Gmili, P. L. Voss, K. Pantzas, T. Moudakir, A. Ougazzaden, D. J. Rogers, F. Hosseini Teherani, V. E. Sandana, P. Bove, K. Prior, R. McClintock & M. Razeghi Proc. SPIE 8987, Oxide-based Materials and Devices V, 898719-- April 2, 2014 ...[Visit Journal] Free-standing (0002)-oriented GaN substrates (f = 2”) were coated with 200 nm of ZnO and used as templates for the growth of GaN thin films. SEM and AFM revealed that such GaN layers had a relatively homogenous surface morphology with an RMS roughness (5 μm x 5 μm) of less than 4nm. XRD studies revealed strained ZnO growth on the GaN substrate and the reproduction of the substrate rocking curve for the GaN overlayers after only a hundred nm of growth, thus indicating that the GaN films had superior crystallographic quality compared to those grown on sapphire or ZnO/sapphire substrates. Quarter-wafer areas of GaN were removed from the GaN substrate (by selective chemical etching away of the ZnO interlayer). The expensive GaN substrates were then reclaimed/reused (without the need for polishing) for a second cycle of ZnO and GaN growth, which gave similar XRD, SEM, CL and AFM results to the first cycle. [reprint (PDF)]
17.	High-speed free-space optical communications based on quantum cascade lasers and type-II superlattice detectors Stephen M. Johnson; Emily Dial; M. Razeghi Proc. SPIE 11288, Quantum Sensing and Nano Electronics and Photonics XVII, 1128814-- January 31, 2020 ...[Visit Journal] Free-space optical communications (FSOC) is a promising avenue for point-to-point, high-bandwidth, and high-security communication links. It has the potential to solve the “last mile” problem modern communication systems face, allowing for high-speed communication links without the expensive and expansive infrastructure required by fiber optic and wireless technologies 1 . Although commercial FSOC systems currently exist, due to their operation in the near infrared and short infrared ranges, they are necessarily limited by atmospheric absorption and scattering losses 2 . Mid-infrared (MWIR) wavelengths are desirable for free space communications systems because they have lower atmospheric scattering losses compared to near-infrared communication links. This leads to increased range and link uptimes. Since this portion of the EM spectrum is unlicensed, link establishment can be implemented quickly. Quantum cascade lasers (QCL) are ideal FSOC transmitters because their emission wavelength is adjustable to MWIR 3 . Compared to the typical VCSEL and laser diodes used in commercial NIR and SWIR FSOC systems, however, they require increased threshold and modulation currents 4 . Receivers based on type-II superlattice (T2SL) detectors are desired in FSOC for their low dark current, high temperature operation, and band gap tunable to MWIR 5. In this paper, we demonstrate the implementation of a high-speed FSOC system using a QCL and a T2SL detector. [reprint (PDF)]
17.	High operability 1024 x 1024 long wavelength infrared focal plane array base on Type-II InAs/GaSb superlattice A. Haddadi, S.R. Darvish, G. Chen, A.M. Hoang, B.M. Nguyen and M. Razeghi AIP Conference Proceedings, Vol. 1416, p. 56-58_NGS15 Conf_Blacksburg, VA_Aug 1-5, 2011-- December 31, 2011 ...[Visit Journal] Fabrication and characterization of a high performance 1024×1024 long wavelength infrared type‐II superlattice focal plane array are described. The FPA performs imaging at a continous rate of 15.00 frames/sec. Each pixel has pitch of 18μm with a fill factor of 71.31%. It demonstrates excellent operability of 95.8% and 97.4% at 81 and 68K operation temperature. The external quantum efficiency is ∼81% without any antireflective coating. Using F∕2 optics and an integration time of 0.13ms, the FPA exhibits an NEDT as low as 27 and 19mK at operating temperatures of 81 and 68K respectively. [reprint (PDF)]

Page 2 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)