Center for Quantum Devices - Most Downloaded Journal Articles

Page 16 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (736 Items)

14.	High operating temperature 320 x 256 middle-wavelength infrared focal plane array imaging based on an InAs/InGaAs/InAlAs/InP quantum dot infrared photodetector S. Tsao, H. Lim, W. Zhang, and M. Razeghi Virtual Journal of Nanoscale Science and Technology-- May 28, 2007 ...[Visit Journal][reprint (PDF)]
14.	Investigations on the substrate dependence of the properties in nominally-undoped β-Ga2O3 thin films grown by PLD F. H. Teherani ; D. J. Rogers ; V. E. Sandana ; P. Bove ; C. Ton-That ; L. L. C. Lem ; E. Chikoidze ; M. Neumann-Spallart ; Y. Dumont ; T. Huynh ; M. R. Phillips ; P. Chapon ; R. McClintock ; M. Razeghi Proc. SPIE 10105, Oxide-based Materials and Devices VIII, 101051R-OLD-- March 23, 2017 ...[Visit Journal] Nominally-undoped Ga₂O₃ layers were deposited on a-, c- and r-plane sapphire substrates using pulsed laser deposition. Conventional x-ray diffraction analysis for films grown on a- and c-plane sapphire showed the layers to be in the β-Ga₂O₃ phase with preferential orientation of the (-201) axis along the growth direction. Pole figures revealed the film grown on r-plane sapphire to also be in the β-Ga₂O₃ phase but with epitaxial offsets of 29.5°, 38.5° and 64° from the growth direction for the (-201) axis. Optical transmission spectroscopy indicated that the bandgap was ~5.2eV, for all the layers and that the transparency was > 80% in the visible wavelength range. Four point collinear resistivity and Van der Pauw based Hall measurements revealed the β-Ga₂O₃ layer on r-plane sapphire to be 4 orders of magnitude more conducting than layers grown on a- and c-plane sapphire under similar conditions. The absolute values of conductivity, carrier mobility and carrier concentration for the β-Ga₂O₃ layer on r-sapphire (at 20Ω-1.cm^-1, 6 cm²/Vs and 1.7 x 10¹⁹ cm^-3, respectively) all exceeded values found in the literature for nominally-undoped β-Ga₂O₃ thin films by at least an order of magnitude. Gas discharge optical emission spectroscopy compositional depth profiling for common shallow donor impurities (Cl, F, Si and Sn) did not indicate any discernable increase in their concentrations compared to background levels in the sapphire substrate. It is proposed that the fundamentally anisotropic conductivity in β-Ga₂O₃ combined with the epitaxial offset of the (-201) axis observed for the layer grown on r-plane sapphire may explain the much larger carrier concentration, electrical conductivity and mobility compared with layers having the (-201) axis aligned along the growth direction. [reprint (PDF)]
14.	High quantum efficiency two color type-II InAs/GaSb n-i-p-p-i-n photodiodes P.Y. Delaunay, B.M. Nguyen, D. Hoffman, A. Hood, E.K. Huang, M. Razeghi, and M.Z. Tidrow Applied Physics Letters, Vol. 92, No. 11, p. 111112-1-- March 17, 2008 ...[Visit Journal] A n-i-p-p-i-n photodiode based on type-II InAs/GaSb superlattice was grown on a GaSb substrate. The two channels, with respective 50% of responsivity cutoff wavelengths at 7.7 and 10 µm, presented quantum efficiencies (QEs) of 47% and 39% at 77 K. The devices can be operated as two diodes for simultaneous detection or as a single n-i-p-p-i-n detector for sequential detection. In the latter configuration, the QEs at 5.3 and 8.5 µm were measured as high as 40% and 39% at 77 K. The optical cross-talk between the two channels could be reduced from 0.36 to 0.08 by applying a 50 mV bias. [reprint (PDF)]
14.	Generation-recombination and trap-assisted tunneling in long wavelength infrared minority electron unipolar photodetectors based on InAs/GaSb superlattice F. Callewaert, A.M. Hoang, and M. Razeghi Applied Physics Letters, 104, 053508 (2014)-- February 6, 2014 ...[Visit Journal] A long wavelength infrared minority electron unipolar photodetector based on InAs/GaSb type-II superlattices is demonstrated. At 77 K, a dark current of 3 × 10⁻⁵ A/cm² and a differential resistance-area of 3 700 Ω·cm² are achieved at the turn-on bias, with a 50%-cutoff of 10.0 μm and a specific detectivity of 6.2 × 10¹¹ Jones. The dark current is fitted as a function of bias and temperature using a model combining generation-recombination and trap-assisted tunneling. Good agreement was observed between the theory and the experimental dark current. [reprint (PDF)]
14.	Aluminum nitride films on different orientations of sapphire and silicon K. Dovidenko, S. Oktyabrsky, J. Narayan, and M. Razeghi Journal of Applied Physics79 (5)-- March 1, 1996 ...[Visit Journal] The details of epitaxial growth and microstrictural characteristics of AlN films grown on sapphire (0001), (1012) and Si (100), (111) substrates were investigated using plan‐view and cross‐sectional high‐resolution transmission electron microscopy and x‐ray diffraction techniques. The films were grown by metalorganic chemical vapor deposition using TMA1+NH3+N2 gas mixtures. Different degrees of epitaxy were observed for the films grown on α‐Al₂O₃ and Si substrates in different orientations. The epitaxial relationship for (0001) sapphire was found to be (0001)AlN∥(0001)sap with in‐plane orientation relationship of [0110]AlN∥[1210]sap. This is equivalent to a 30° rotation in the basal (0001) plane. For (1012) sapphire substrates, the epitaxial relationship was determined to be (1120)AlN∥(1012)sap with the in‐plane alignment of [0001]AlN∥[1011]sap. The AlN films on (0001) α‐Al₂O₃ were found to contain inverted domain boundaries and a/3〈1120〉 threading dislocations with the estimated density of 10¹⁰ cm⁻². The density of planar defects (stacking faults) found in AlN films was considerably higher in the case of (1012) compared to (0001) substrates. Films on Si substrates were found to be highly textured c axis oriented when grown on (111) Si, and c axis textured with random in‐plane orientation on (100) Si. The role of thin‐film defects and interfaces on device fabrication is discussed. [reprint (PDF)]
14.	Conduction‐ and valence‐band offsets in GaAs/Ga0.51In0.49P single quantum wells grown by metalorganic chemical vapor deposition D. Biswas; N. Debbar; P. Bhattacharya; M. Razeghi; M. Defour; F. Omnes Appl. Phys. Lett. 56, 833–835 (1990)-- February 26, 1990 ...[Visit Journal] We have independently estimated the conduction- and valence-band offsets D.Ec and D.Ev in GaAs/Gao . 51 Ino49 P quantum wells by measuring the capacitance transient resulting from thermal emission of carriers from the respective wens. The heterostructure samples were grown by low-pressure metalorganic chemical vapor deposition. The band offsets are extrapolated from the emission activation energies with appropriate corrections. The estimated values of AEc and AEv are 0.198 and 0.285 eV, respectively. [reprint (PDF)]
14.	Crystallography of epitaxial growth of wurtzite-type thin films on sapphire substrates P. Kung, C.J. Sun, A. Saxler, H. Ohsato, and M. Razeghi Journal of Applied Physics 75 (9)-- May 1, 1994 ...[Visit Journal] In this article, we present a crystallographic model to describe the epitaxial growth of wurtzite‐type thin films such as gallium nitride (GaN) on different orientations of sapphire (Al2O3) substrates. Through this model, we demonstrate the thin films grown on (00⋅1)Al₂O₃ have a better epilayer‐substrate interface quality than those grown on (01⋅2)Al₂O₃. We also show the epilayer grown on (00⋅1)Al₂O₃ are gallium‐terminated, and both (00⋅1) and (01⋅2) surfaces of sapphire crystals are oxygen‐terminated. [reprint (PDF)]
14.	High performance mid-wavelength quantum dot infrared photodetectors for focal plane arrays M. Razeghi, H. Lim, S. Tsao, M. Taguchi, W. Zhang and A.A. Quivy SPIE Conference, San Diego, CA, Vol. 6297, pp. 62970C-- August 13, 2006 ...[Visit Journal] Quantum dot infrared photodetectors (QDIPs) have recently emerged as promising candidates for detection in the middle wavelength infrared (MWIR) and long wavelength infrared (LWIR) ranges. Here, we report our recent results for mid-wavelength QDIPs grown by low-pressure metalorganic chemical vapor deposition. Three monolayer of In_0.68Ga_0.32As self-assembled via the Stranski-Krastanov growth mode and formed lens-shaped InGaAs quantum dots with a density around 3×10₁₀ cm^-2. The peak responsivity at 77 K was measured to be 3.4 A/W at a bias of -1.9 V with 4.7 µm peak detection wavelength. Focal plane arrays (FPAs) based on these devices have been developed. The preliminary result of FPA imaging is presented. [reprint (PDF)]
14.	High speed type-II superlattice based photodetectors transferred on sapphire Arash Dehzangi, Ryan McClintock, Donghai Wu, Jiakai Li, Stephen Johnson, Emily Dial and Manijeh Razeghi Applied Physics Express, Volume 12, Number 11-- October 3, 2019 ...[Visit Journal] We report the substrate transfer of InAs/GaSb/AlSb based type-II superlattice (T2SL) e-SWIR photodetector from native GaSb substrates to low loss sapphire substrate in order to enhance the frequency response of the device. We have demonstrated the damage-free transfer of T2SL-based thin-films to sapphire substrate using top–down processing and a chemical epilayer release technique. After transfer the −3 dB cut-off frequency increased from 6.4 GHz to 17.2 GHz, for 8 μm diameter circular mesas under -15 V applied bias. We also investigated the cut-off frequency verses applied bias and lateral scaling to assess the limitations for even higher frequency performance. Direct Link [reprint (PDF)]
14.	First Demonstration of ~ 10 microns FPAs in InAs/GaSb SLS M. Razeghi, P.Y. Delaunay, B.M. Nguyen, A. Hood, D. Hoffman, R. McClintock, Y. Wei, E. Michel, V. Nathan and M. Tidrow IEEE LEOS Newsletter 20 (5)-- October 1, 2006 ...[Visit Journal] The concept of Type-II InAs/GaSb superlattice was first brought by Nobel Laureate L. Esaki, et al. in the 1970s. There had been few studies on this material system until two decades later when reasonable quality material growth was made possible using molecular beam epitaxy. With the addition of cracker cells for the group V sources and optimizations of material growth conditions, the superlattice quality become significantly improved and the detectors made of these superlattice materials can meet the demand in some practical field applications. Especially in the LWIR regime, it provides a very promising alternative to HgCdTe for better material stability and uniformity, etc. We have developed the empirical tight binding model (ETBM) for precise determination of the superlattice bandgap. [reprint (PDF)]
14.	Optical Investigations of GaAs-GaInP Quantum Wells and Superlattices Grown by Metalorganic Chemical Vapor Deposition Omnes F., and Razeghi M. Applied Physics Letters 59 (9), p. 1034-- May 28, 1991 ...[Visit Journal] Recent experimental results on the photoluminescence and photoluminescence excitation of GaAs‐Ga_0.51In_0.49P lattice‐matched quantum wells and superlattices are discussed. The full width at half maximum of a 10‐period GaAs‐GaInP superlattice with Lz=90 Å and LB=100 Å is 4 meV at 4 K. The photoluminescence excitation exhibits very sharp peaks attributed to the electron to light‐hole and electron to heavy‐hole transitions. The GaInP‐GaAs interface suffers from memory effect of In, rather than P or As elements. [reprint (PDF)]
14.	Two‐dimensional electron gas in a In0.53Ga0.47As‐InP heterojunction grown by metalorganic chemical vapor deposition Y. Guldner; J. P. Vieren; P. Voisin; M. Voos; M. Razeghi; M. A. Poisson Y. Guldner, J. P. Vieren, P. Voisin, M. Voos, M. Razeghi, M. A. Poisson; Two‐dimensional electron gas in a In0.53Ga0.47As‐InP heterojunction grown by metalorganic chemical vapor deposition. Appl. Phys. Lett. 15 May 1982; 40 (10): 877–879.-- April 15, 1982 ...[Visit Journal] We report, from Shubnikov-de Haas and cyclotron resonance experiments, the first observation of a two-dimensional, high-mobility electron gas in a selectively doped 1110.53 G~l.47 As-InP heterojunction grown by metalorganic chemical vapor deposition. Several parameters of the electronic system under consideration are determined. [reprint (PDF)]
14.	Harmonic injection locking of high-power mid-infrared quantum cascade lasers Feihu Wang, Steven Slivken, and Manijeh Razeghi OSA Photonics Research •https://doi.org/10.1364/PRJ.423573 ...[Visit Journal] High-power, high-speed quantum cascade lasers (QCLs) with stable emission in the mid-infrared regime are of great importance for applications in metrology, telecommunication, and fundamental tests of physics. Owing to the inter-sub-band transition, the unique ultrafast gain recovery time of the QCL with picosecond dynamics is expected to overcome the modulation limit of classical semiconductor lasers and bring a revolution for the next generation of ultrahigh-speed optical communication. Therefore, harmonic injection locking, offering the possibility to fast modulate and greatly stabilize the laser emission beyond the rate limited by cavity length, is inherently adapted to QCLs. In this work, we demonstrate for the first time the harmonic injection locking of a mid-infrared QCL with an output power over 1 watt in continuous-wave operation at 288 K. Compared with an unlocked laser, the inter-mode spacing fluctuation of an injection locked QCL can be considerably reduced by a factor above 1×10 E3, which permits the realization of an ultra-stable mid-infrared semiconductor laser with high phase coherence and frequency purity. Despite temperature change, this fluctuation can be still stabilized to hertz level by a microwave modulation up to ∼18 GHz. These results open up the prospect of the applications of mid-infrared QCL technology for frequency comb engineering, metrology and the next generation ultrahigh-speed telecommunication. It may also stimulate new schemes for exploring ultrafast mid-infrared pulse generation in QCLs. [reprint (PDF)]
14.	Thermal analysis of buried heterostructure quantum cascade lasers for long-wavelength infrared emission using 2D anisotropic heat-dissipation model H.K. Lee, K.S. Chung, J.S. Yu and M. Razeghi Physica Status Solidi (a), Vol. 206, p. 356-362-- February 1, 2009 ...[Visit Journal] We have theoretically investigated and compared the thermal characteristics of 10.6 μm InGaAs/InAlAs/InP buried heterostructure (BH) quantum cascade lasers (QCLs) with different heat-sinking configurations by a steady-state heat-transfer analysis. The heat-source densities were obtained from laser threshold power densities measured experimentally under room-temperature continuous-wave mode. The two-dimensional anisotropic heat-dissipation model was used to calculate the temperature distribution, heat flux, and thermal conductance (Gth) inside the device. For good thermal characteristics, the QCLs in the long-wavelength infrared region require the relatively narrow BH structure in combination with epilayer-down bonding due to thick active core/cladding layers and high insulator losses. The single-ridge BH structure results in slightly higher thermal conductance by 2-4% than the double-channel (DC) ridge BH structure. For W = 12 m with 5 μm thick electroplated Au, the single-ridge BH laser with epilayer-down bonding exhibited the highest G_th value of 201.9 W/K cm², i.e. increased by nearly 36% with respect to the epilayer-up bonded DC ridge waveguide laser. This value is improved by 50% and 62% with respect to the single-ridge BH laser and DC ridge waveguide laser with W = 20 μm in the epilayer-up bonding scheme, respectively. [reprint (PDF)]
14.	Temperature dependence of the dark current and activation energy at avalanche onset of GaN Avalanche Photodiodes M.P. Ulmer, E. Cicek, R. McClintock, Z. Vashaei and M. Razeghi SPIE Proceedings, Vol. 8460, p. 84601G-1-- August 15, 2012 ...[Visit Journal] We report a study of the performance of an avalanche photodiode (APD) as a function of temperature from 564 K to 74 K. The dark current at avalanche onset decreases from 564 K to 74 K by approximately a factor of 125 and from 300 K to 74K the dark current at avalanche offset is reduced by a factor of about 10. The drop would have been considerably larger if the activation energy at avalanche onset (Ea) did not also decrease with decreasing temperature. These data give us insights into how to improve the single-photon counting performance of a GaN based ADP. [reprint (PDF)]
14.	1.2–1.6 μm GaxIn1−xAsyP1−y-InP DH lasers grown by LPMOCVD M. Razeghi, B. de Crémoux, J.P. Duchemin M. Razeghi, B. de Crémoux, J.P. Duchemin, 1.2–1.6 μm GaxIn1−xAsyP1−y-InP DH lasers grown by LPMOCVD, Journal of Crystal Growth, Volume 68, Issue 1, 1984, Pages 389-397,-- September 1, 1984 ...[Visit Journal] Room temperature pulse operation and continuous wave (CW) operation in the 1.2–1.6 μm region have been achieved in GaInAsP-InP DH lasers fabricated on material grown by LPMOCVD. Threshold currents density as low as 430 A/cm2 (cavity length of 950 μm) have been measured for devices emitting at 1.3 μm. Threshold current densities of 1060 A/cm2 (cavity length of 400 μm) have been obtained for devices emitting at 1.55 μm, with active layer thicknesses of 0.22 μm. Values of T0 between 60 and 70 K have been obtained. Fundamental transverse mode oscillation has been achieved (for CW operation) up to an output power of 10 mW. The preliminary results on the aging test are most encouraging and demonstrate that the LPMOCVD lasers emitting at 1.2–1.6 μm have comparable degradation rates to those of LPE lasers suggesting the LPMOCVD technique is promising for large scale production of laser diodes. [reprint (PDF)]
14.	Gain and recombination dynamics in photodetectors made with quantum nanostructures: the quantum dot in a well and the quantum well B. Movaghar, S. Tsao, S. Abdollahi Pour, T. Yamanaka, and M. Razeghi Virtual Journal of Nanoscale Science & Technology, Vol. 18, No. 14-- October 6, 2008 ...[Visit Journal][reprint (PDF)]
14.	Background limited performance of long wavelength infrared focal plane arrays fabricated from type-II InAs/GaSb M-structure superlattice P.Y. Delaunay, B.M. Nguyen and M. Razeghi SPIE Porceedings, Vol. 7298, Orlando, FL 2009, p. 72981Q-- April 13, 2009 ...[Visit Journal] Recent advances in growth techniques, structure design and processing have lifted the performance of Type-II InAs/GaSb superlattice photodetectors. The introduction of a M-structure design improved both the dark current and R0A of Type-II photodiodes. This new structure combined with a thick absorbing region demonstrated background limited performance at 77K for a 300K background and a 2-π field of view. A focal plane array with a 9.6 μm 50% cutoff wavelength was fabricated with this design and characterized at 80K. The dark current of individual pixels was measured around 1.3 nA, 7 times lower than previous superlattice FPAs. This led to a higher dynamic range and longer integration times. The quantum efficiency of detectors without anti-reflective coating was 72%. The noise equivalent temperature difference reached 23 mK. The deposition of an anti-reflective coating improved the NEDT to 20 mK and the quantum efficiency to 89%. [reprint (PDF)]
14.	Very High Average Power at Room Temperature from λ ~ 5.9 μm Quantum Cascade Lasers J.S. Yu, S. Slivken, A. Evans, J. David and M. Razeghi Virtual Journal of Nanoscale Science & Technology 26-- May 26, 2003 ...[Visit Journal][reprint (PDF)]
14.	Electron-spin resonance of the two-dimensional electron gas in Ga0.47In0.53As-InP heterostructures M. Dobers, J. P. Vieren,, Y. Guldner P. Bove, F. Omnes, and M. Razeghi Phys. Rev. B 40, 8075(R) – Published 15 October, 1989-- October 15, 1989 ...[Visit Journal] The microwave-induced change of the magnetoresistivity of Ga0.47In0.53As-InP heterostructures reveals resonant structure which is attributed to electron-spin resonance of the two-dimensional conduction electrons. With microwave frequencies up to 480 GHz and in magnetic fields up to 12 T, we studied the spin splitting of the two lowest Landau levels in different samples. The spin splitting of these Landau levels is a quadratic function of the magnetic field and its extrapolation to zero magnetic field leads to vanishing spin splitting. The g factors depend on the magnetic field B and the Landau level N as follows: g(B,N)=𝑔0-c(N+1/2)B, where 𝑔0 and c are sample-dependent parameters, which are of the order of 𝑔0≊4.1 and c≊0.08 T−1, in the studied heterostructures. [reprint (PDF)]
14.	Type-II InAs/GaSb photodiodes and focal plane arrays aimed at high operating temperatures M. Razeghi, S. Abdollahi Pour, E.K. Huang, G. Chen, A. Haddadi, and B.M. Nguyen Opto-Electronics Review (OER), Vol. 19, No. 3, June 2011, p. 46-54-- June 1, 2011 ...[Visit Journal] Recent efforts to improve the performance of type-II InAs/GaSb superlattice photodiodes and focal plane arrays (FPA) have been reviewed. The theoretical bandstructure models have been discussed first. A review of recent developments in growth and characterization techniques is given. The efforts to improve the performance of MWIR photodiodes and focal plane arrays (FPAs) have been reviewed and the latest results have been reported. It is shown that these improvements has resulted in background limited performance (BLIP) of single element photodiodes up to 180 K. FPA shows a constant noise equivalent temperature difference (NEDT) of 11 mK up to 120 K and it shows human body imaging up to 170 K. [reprint (PDF)]
14.	High differential resistance type-II InAs/GaSb superlattice photodiodes for the long-wavelength infrared A. Hood, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E. Michel and M. Razeghi Applied Physics Letters, 89 (9)-- August 28, 2006 ...[Visit Journal] Type-II InAs/GaSb superlattice photodiodes with a 50% cutoff wavelength ranging from 11 to 13 μm are presented. Optimization of diffusion limited photodiodes provided superlattice structures for improved injection efficiency in direct injection hybrid focal plane array applications. [reprint (PDF)]
14.	High Quantum Efficiency Solar-Blind Photodetectors R. McClintock, A. Yasan, K. Mayes, D. Shiell, S. Darvish, P. Kung and M. Razeghi SPIE Conference, Jose, CA, Vol. 5359, pp. 434-- January 25, 2004 ...[Visit Journal] We report AlGaN-based back-illuminated solar-blind p-i-n photodetectors with a record peak responsivity of 150 mA/W at 280 nm, corresponding to a high external quantum efficiency of 68%, increasing to 74% under 5 volts reverse bias. Through optimization of the p-AlGaN layer, we were able to remove the out-of-band negative photoresponse originating from the Schottky-like p-type metal contact, and hence significantly improve the degree of solar-blindness [reprint (PDF)]
14.	GaInAs/InP nanopillar arrays for long wavelength infrared detection A. Gin, Y. Wei, A. Hood, D. Hoffman, M. Razeghi and G.J. Brown SPIE Conference, Jose, CA, Vol. 5732, pp. 350-- January 22, 2005 ...[Visit Journal] Nanopillar devices have been fabricated from GaInAs/InP QWIP material grown by MOCVD. Using electron beam lithography and reactive ion etching techniques, large, regular arrays of nanopillars with controllable diameters ranging from 150 nm to less than 40 nm have been reproducibly formed. Photoluminescence experiments demonstrate a strong peak wavelength blue shift for nanopillar structures compared to the as-grown quantum well material. Top and bottom metal contacts have been realized using a polyimide planarization and etchback procedure. I-V and noise measurements have been performed. Optical measurements indicate photoconductive response in selected nanopillar arrays. Device peak wavelength response occurs at about 8 µm with peak device responsivity of 420 mA/W. Peak detectivity of 3×10⁸ cm·Hz^½/W has been achieved at -1V bias and 30 K. [reprint (PDF)]
14.	Relaxation kinetics in quantum cascade laser S. Slivken, V. Litvinov, M. Razeghi, and J.R. Meyer Journal of Applied Physics 85 (2)-- January 15, 1999 ...[Visit Journal] Relaxation kinetics in a quantum cascade intersubband laser are investigated. Distribution functions and gain spectra of a three-subband double-quantum-well active region are obtained as a function of temperature and injection current. The potentially important role of the nonequilibrium phonons at lasing threshold is shown and discussed in details. It is shown that the threshold current is strongly dependent of the power dissipated in the active region in steady state. The numerical calculations for an 8.5 μm laser illustrate the general issues of relaxation kinetics in quantum cascade lasers. Temperature dependence of the threshold current is obtained in a good agreement with the experiments. [reprint (PDF)]

Page 16 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (736 Items)