Center for Quantum Devices - Most Downloaded Journal Articles

Page 13 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (737 Items)

15.	Growth of “moth-eye” ZnO nanostructures on Si(111), c-Al2O3, ZnO and steel substrates by pulsed laser deposition Vinod E. Sandana, David J. Rogers, Ferechteh Hosseini Teherani, Philippe Bove, Michael Molinari, Michel Troyon, Alain Largeteau, Gérard Demazeau, Colin Scott, Gaelle Orsal, Henri-Jean Drouhin, Abdallah Ougazzaden, Manijeh Razeghi Phys. Status Solidi C., 1-5 (2013)-- August 6, 2013 ...[Visit Journal] Self-forming, vertically-aligned, arrays of black-body-like ZnO moth-eye nanostructures were grown on Si(111), c-Al₂O₃, ZnO and high manganese austenitic steel substrates using Pulsed Laser Deposition. X-ray diffraction (XRD) revealed the nanostructures to be well-crystallised wurtzite ZnO with strong preferential c-axis crystallographic orientation along the growth direction for all the substrates. Cathodoluminescence (CL) studies revealed emission characteristic of the ZnO near band edge for all substrates. Such moth-eye nanostructures have a graded effective refractive index and exhibit black-body characteristics. Coatings with these features may offer improvements in photovoltaic and LED performance. Moreover, since ZnO nanostructures can be grown readily on a wide range of substrates it is suggested that such an approach could facilitate growth of GaN-based devices on mismatched and/or technologically important substrates, which may have been inaccessible till present. [reprint (PDF)]
15.	Negative luminescence of InAs/GaSb superlattice photodiodes F. Fuchs, D. Hoffman, A. Gin, A. Hood, Y. Wei, and M. Razeghi Phys. Stat. Sol. C 3 (3)-- February 22, 2006 ...[Visit Journal] The emission behaviour of InAs/GaSb superlattice photodiodes has been studied in the spectral range between 8 µm and 13 μm. With a radiometric calibration of the experimental set-up the internal quantum efficiency has been determined in the temperature range between 80 K and 300 K for both, the negative and positive luminescence. The quantitative analysis of the internal quantum efficiency of the non-equilibrium radiation enables the determination of the Auger coefficient. [reprint (PDF)]
15.	Semiconductor ultraviolet detectors M. Razeghi and A. Rogalski Journal of Applied Physics Applied Physics Review 79 (10)-- May 15, 1996 ...[Visit Journal] In this review article a comprehensive analysis of the developments in ultraviolet (UV) detector technology is described. At the beginning, the classification of UV detectors and general requirements imposed on these detectors are presented. Further considerations are restricted to modern semiconductor UV detectors, so the basic theory of photoconductive and photovoltaic detectors is presented in a uniform way convenient for various detector materials. Next, the current state of the art of different types of semiconductor UV detectors is presented. Hitherto, the semiconductor UV detectors have been mainly fabricated using Si. Industries such as the aerospace, automotive, petroleum, and others have continuously provided the impetus pushing the development of fringe technologies which are tolerant of increasingly high temperatures and hostile environments. As a result, the main efforts are currently directed to a new generation of UV detectors fabricated from wide band-gap semiconductors the most promising of which are diamond and AlGaN. The latest progress in development of AlGaN UV detectors is finally described in detail. [reprint (PDF)]
15.	Development of Quantum Cascade Lasers for High Peak Output Power and Low Threshold Current Density S. Slivken and M. Razeghi Solid State Electronics 46-- January 1, 2002 ...[Visit Journal] Design and material optimization are used to both decrease the threshold current density and increase the output power for quantum cascade lasers. Waveguides are designed to try and minimize free-carrier and surface-plasmon absorption. Excellent material characterization is also presented, showing excellent control over layer thickness, interface quality, and doping level. Experiments are done to both optimize the injector doping level and to maximize the output power from a single aperture. At 300 K, a threshold current density as low as 1.8 kA/cm² is reported, along with peak powers of approximately 2.5 W. Strain-balanced lasers are also demonstrated at λnot, vert, similar5 μm, exhibiting threshold current densities<300 A/cm² at 80 K. These values represent the state-of-the-art for mid-infrared lasers with λ>4 μm [reprint (PDF)]
15.	Solar-Blind Deep UV Avalanche Photodetectors Using Reduced Area Epitaxy Lakshay Gautam , Junhee Lee, Michael Richards, and Manijeh Razeghi , Lakshay Gautam, Manijeh Razeghi, IEEE JOURNAL OF QUANTUM ELECTRONICS, VOL. 59, NO. 6, 10.1109/JQE.2023.3325254 ...[Visit Journal] We report high gain avalanche photodetectors operating in the deep UV wavelength regime. The high gain was leveraged through reduced area epitaxy by patterning AlN on Sapphire substrate. This helps in a substantial reduction of crack formation due to overgrowth on individually isolated AlN mesas. Reproducible gain on the order of 105 was reported for multiple diodes in different areas of 320 × 256 focal plane array. [reprint (PDF)]
15.	GaN avalanche photodiodes grown on m-plane freestanding GaN substrate Z. Vashaei, E. Cicek, C. Bayram, R. McClintock and M. Razeghi Applied Physics Letters, Vol. 96, No. 20, p. 201908-1-- May 17, 2010 ...[Visit Journal] M-plane GaN avalanche p-i-n photodiodes on low dislocation density freestanding m-plane GaN substrates were realized using metal-organic chemical vapor deposition. High quality homoepitaxial m-plane GaN layers were developed; the root-mean-square surface roughness was less than 1 Å and the full-width-at-half-maximum value of the x-ray rocking curve for (1010) diffraction of m-plane GaN epilayer was 32 arcsec. High quality material led to a low reverse-bias dark current of 8.11 pA for 225 μm² mesa photodetectors prior to avalanche breakdown, with the maximum multiplication gain reaching about 8000. [reprint (PDF)]
15.	Broad area photonic crystal distributed feedback quantum cascade lasers emitting 34 W at λ ~ 4.36 μm B. Gokden, Y. Bai, N. Bandyopadhyay, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 97, No. 13, p. 131112-1-- September 27, 2010 ...[Visit Journal] We demonstrate room temperature, high power, single mode, and diffraction limited operation of a two dimensional photonic crystal distributed feedback quantum cascade laser emitting at 4.36 μm. Total peak power up to 34 W is observed from a 3 mm long laser with 400 μm cavity width at room temperature. Far-field profiles have M2 figure of merit as low as 2.5. This device represents a significant step toward realization of spatially and spectrally pure broad area high power quantum cascade lasers. [reprint (PDF)]
15.	Geiger-mode operation of ultraviolet avalanche photodiodes grown on sapphire and free-standing GaN substrates E. Cicek, Z. Vashaei, R. McClintock, C. Bayram, and M. Razeghi Applied Physics Letters, Vol. 96, No. 26, p. 261107 (2010);-- June 28, 2010 ...[Visit Journal] GaN avalanche photodiodes (APDs) were grown on both conventional sapphire and low dislocation density free-standing (FS) c-plane GaN substrates. Leakage current, gain, and single photon detection efficiency (SPDE) of these APDs were compared. At a reverse-bias of 70 V, APDs grown on sapphire substrates exhibited a dark current density of 2.7×10⁻⁴ A/cm² whereas APDs grown on FS-GaN substrates had a significantly lower dark current density of 2.1×10⁻⁶ A/cm². Under linear-mode operation, APDs grown on FS-GaN achieved avalanche gain as high as 14 000. Geiger-mode operation conditions were studied for enhanced SPDE. Under front-illumination the 625 μm² area APD yielded a SPDE of 13% when grown on sapphire substrates compared to more than 24% when grown on FS-GaN. The SPDE of the same APD on sapphire substrate increased to 30% under back-illumination—the FS-GaN APDs were only tested under front illumination due to the thick absorbing GaN substrate. [reprint (PDF)]
15.	Continuous wave, room temperature operation of λ ~ 3μm quantum cascade laser N. Bandyopadhyay, Y. Bai, S. Tsao, S. Nida, S. Slivken and M. Razeghi SPIE Proceedings, Vol. 8631, p. 86310M-1, Photonics West, San Francisco, CA-- February 3, 2013 ...[Visit Journal] Quantum Cascade Lasers (QCLs), operating in continuous wave (CW) at room temperature(RT) in 3-3.5 μm spectral range, which overlaps the spectral fingerprint region of many hydrocarbons, is essential in spectroscopic trace gas detection, environment monitoring, and pollution control. A 3 μm QCL, operating in CW at RT is demonstrated. This initial result makes it possible, for the most popular material system (AlInAs/GaInAs on InP) used in QCLs in mid-infrared and long-infrared, to cover the entire spectral range of mid-infrared atmospheric window (3-5 μm). In_0.79Ga_0.21As/In_0.11Al_0.89As strain balanced superlattice, which has a large conduction band offset, was grown. The strain was balanced with composite barriers (In_0.11Al_0.89As /In_0.4Al_0.6As) in the injector region, to eliminate the need of extremely high compressively strained GaInAs, whose pseudomorphic growth is very difficult. [reprint (PDF)]
15.	Review of high power frequency comb sources based on InP From MIR to THZ at CQD Manijeh Razeghi, Quanyong Lu, Donghai Wu, Steven Slivken Event: SPIE Optical Engineering + Applications, 2018, San Diego, California, United States-- September 14, 2018 ...[Visit Journal] We present the recent development of high performance compact frequency comb sources based on mid-infrared quantum cascade lasers. Significant performance improvements of our frequency combs with respect to the continuous wave power output, spectral bandwidth, and beatnote linewidth are achieved by systematic optimization of the device's active region, group velocity dispersion, and waveguide design. To date, we have demonstrated the most efficient, high power frequency comb operation from a free-running room temperature continuous wave (RT CW) dispersion engineered QCL at λ~5-9 μm. In terms of bandwidth, the comb covered a broad spectral range of 120 cm⁻¹ with a radio-frequency intermode beatnote spectral linewidth of 40 Hz and a total power output of 880 mW at 8 μm and 1 W at ~5.0 μm. The developing characteristics show the potential for fast detection of various gas molecules. Furthermore, THz comb sources based on difference frequency generation in a mid-IR QCL combs could be potentially developed. [reprint (PDF)]
15.	Effect of sidewall surface recombination on the quantum efficiency in a Y₂O₃ passivated gated type-II InAs/GaSb long-infrared photodetector array G. Chen, A. M. Hoang, S. Bogdanov, A. Haddadi, S. R. Darvish, and M. Razeghi Appl. Phys. Lett. 103, 223501 (2013)-- November 25, 2013 ...[Visit Journal] Y₂O₃ was applied to passivate a long-wavelength infrared type-II superlattice gated photodetector array with 50% cut-off wavelength at 11 μm, resulting in a saturated gate bias that was 3 times lower than in a SiO₂ passivated array. Besides effectively suppressing surface leakage, gating technique exhibited its ability to enhance the quantum efficiency of 100 × 100 μm size mesa from 51% to 57% by suppressing sidewall surface recombination. At 77 K, the gated photodetector showed dark current density and resistance-area product at −300 mV of 2.5 × 10⁻⁵ A/cm² and 1.3 × 10⁴ Ω·cm², respectively, and a specific detectivity of 1.4 × 10¹² Jones. [reprint (PDF)]
15.	High Quality Aluminum Nitride Epitaxial Layers Grown on Sapphire Substrates A. Saxler, P. Kung, C.J. Sun, E. Bigan and M. Razeghi Applied Physics Letters 64 (3)-- January 17, 1994 ...[Visit Journal] In this letter we report the growth of high quality AlN epitaxial layers on sapphire substrates. The AlN grown on (00·1) sapphire exhibited a better crystalline quality than that grown on (01·2) sapphire. An x-ray rocking curve of AlN on (00·1) Al₂O₃ yielded a full width at half-maximum of 97.2 arcsec, which is the narrowest value reported to our knowledge. The AlN peak on (01·2) Al₂O₃ was about 30 times wider. The absorption edge measured by ultraviolet transmission spectroscopy for AlN grown on (00·1) Al₂O₃ was about 197 nm. [reprint (PDF)]
15.	Compressively-strained multiple quantum well InAsSb lasers emitting at 3.6 μm grown by metal-organic chemical vapor deposition B. Lane, D. Wu, A. Rybaltowski, H. Yi, J. Diaz, and M. Razeghi Applied Physics Letters 70 (4)-- January 27, 1997 ...[Visit Journal] A compressively strained InAsSb/InAs multiple quantum-well (MQW) structure was grown by low-pressure metal-organic chemical vapor deposition. Maximum output power (from two facets) up to 1 W with differential efficiency about 70% was obtained from a MQW laser with stripe width of 100 μm and cavity length of 700 μm for emitting wavelength of 3.65 μm at 90 K in pulse mode operation. About 2 times lower threshold current density was obtained from the MQW lasers for a temperature range of 90 to 140 K compared to the double heterostructure lasers grown on the same growth conditions. [reprint (PDF)]
15.	Demonstration of type-II superlattice MWIR minority carrier unipolar imager for high operation temperature application Guanxi Chen, Abbas Haddadi, Anh-Minh Hoang, Romain Chevallier, and Manijeh Razeghi Optics Letters Vol. 40, Iss. 1, pp. 29–32-- December 18, 2014 ...[Visit Journal] An InAs/GaSb type-II superlattice-based mid-wavelength infrared (MWIR) 320×256 unipolar focal plane array (FPA) using pMp architecture exhibited excellent infrared image from 81 to 150 K and ∼98% operability, which illustrated the possibility for high operation temperature application. At 150 K and −50 mV operation bias, the 27 μm pixels exhibited dark current density to be 1.2×10⁻⁵ A/cm², with 50% cutoff wavelength of 4.9 μm, quantum efficiency of 67% at peak responsivity (4.6 μm), and specific detectivity of 1.2×10¹² Jones. At 90 K and below, the 27 μm pixels exhibited system limited dark current density, which is below 1×10⁻⁹ A/cm², and specific detectivity of 1.5×10¹⁴ Jones. From 81 to 100 K, the FPA showed ∼11 mK NEDT by using F/2.3 optics and a 9.69 ms integration time. [reprint (PDF)]
15.	High-responsivity GaInAs/InP Quantum Well Infrared Photodetectors Grown by Low-Pressure Metalorganic Chemical Vapor Deposition M. Erdtmann, A. Matlis, C. Jelen, M. Razeghi, and G. Brown SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] We have studied the dependence of the well doping density in n-type GaInAs/InP quantum well IR photodetectors (QWIPs) grown by low-pressure metalorganic chemical vapor deposition. Three identical GaInAs/InP QWIP structures were grown with well sheet carrier densities of 1x10¹¹ cm^-2, 3x10¹¹ cm^-2, and 10x10¹¹ cm^-2; all three samples had very sharp spectral response at λ equals 9.0 μm. We find that there is a large sensitivity of responsivity, dark current, noise current, and detectivity with the well doping density. Measurements revealed that the lowest-doped samples had an extremely low responsivity relative to the doping concentration while the highest-doped sample had an excessively high dark current relative to doping. The middle-doped sample yielded the optimal results. This QWIP had a responsivity of 33.2 A/W and operated with a detectivity of 3.5x10¹⁰ cm·Hz^½·W^-1 at a bias of 0.75 V and temperature of 80 K. This responsivity is the highest value reported for any QWIP in the (lambda) equals 8-9 &mus;m range. Analysis is also presented explaining the dependence of the measured QWIP parameters to well doping density. [reprint (PDF)]
15.	Direct growth of thick AlN layers on nanopatterned Si substrates by cantilever epitaxy Ilkay Demir, Yoann Robin, Ryan McClintock, Sezai Elagoz, Konstantinos Zekentes, and Manijeh Razeghi Phys. Status Solidi A, pp. 1–6-- September 30, 2016 ...[Visit Journal] AlN layers have been grown on 200 nm period of nanopatterned Si (111) substrates by cantilever epitaxy and compared with AlN layers grown by maskless lateral epitaxial overgrowth (LEO) on micropatterned Si (111) substrates. The material quality of 5–10 µm thick AlN grown by LEO is comparable to that of much thinner layers (2 µm) grown by cantilever epitaxy on the nanopatterned substrates. Indeed, the latter exhibited root mean square (RMS) roughness of 0.65 nm and X-ray diffraction full width at half-maximum (FWHM) of 710 arcsec along the (0002) reflection and 930 arcsec along the (10̅15) reflection. The corresponding room temperature photoluminescence spectra was dominated by a sharp band edge peak. Back emission ultra violet light emitting diodes (UV LEDs) were fabricated by flip chip bonding to patterned AlN heat sinks followed by complete Si (111) substrate removal demonstrating a peak pulsed power of ∼0.7 mW at 344 nm peak emission wavelength. The demonstrated UV LEDs were fabricated on a cost effective epitaxial structure grown on the nanopatterned Si substrate with a total thickness of 3.3 µm [reprint (PDF)]
15.	Photonic crystal distributed feedback quantum cascade lasers with 12 W output power Y. Bai, B. Gokden, S.R. Darvish, S. Slivken, and M. Razeghi Applied Physics Letters, Vol. 95, No. 3-- July 20, 2009 ...[Visit Journal] We demonstrate room temperature, high power, and diffraction limited operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting around 4.7 µm. PCDFB gratings with three distinctive periods are fabricated on the same wafer. Peak output power up to 12 W is demonstrated. Lasers with different periods show expected wavelength shifts according to the design. Dual mode spectra are attributed to a purer index coupling by putting the grating layer 100 nm away from the laser core. Single lobed diffraction limited far field profiles are observed. [reprint (PDF)]
15.	Recent performance records for mid-IR quantum cascade lasers M. Razeghi; Y. Bai; S. Slivken; S. Kuboya; S.R. Darvish Terahertz and Mid Infrared Radiation: Basic Research and Practical Applications, 2009. TERA-MIR International Workshop [5379656], (2009) -- November 9, 2009 ...[Visit Journal] The wall plug efficiency of the mid-infrared quantum cascade laser in room temperature continuous wave operation is brought to 17%. Peak output power from a broad area (400 μm x 3 mm) device gives 120 W output power in pulsed mode operation at room temperature. Using a single-well-injector design, specifically made for low temperature operation, a record wall plug efficiency of 53% is demonstrated at 40 K. [reprint (PDF)]
15.	High-Power CW Mid-IR Quantum Cascade Lasers J.R. Meyer, W.W. Bewley, J.R. Lindle, I. Vurgaftman, A.J. Evans, J.S. Yu, S. Slivken, and M. Razeghi SPIE Conference, Jose, CA, -- January 22, 2005 ...[Visit Journal] We report the cw operation of quantum cascade lasers that do not require cryogenic cooling and emit at λ = 4.7-6.2 µm. At 200 K, more than 1 W of output power is obtained from 12-µm-wide stripes, with a wall-plug efficiency (η_wall) near 10%. Room-temperature cw operation has also been demonstrated, with a maximum output power of 640 mW (η_wall = 4.5%) at 6 µm and 260 mW (η_wall = 2.3%) at 4.8 µm. Far-field characterization indicates that whereas the beam quality remains close to the diffraction limit in all of the tested lasers, in the devices emitting at 6.2 µm the beam tends to steer by as much as 5-10° degrees in either direction with varying temperature and pump current. [reprint (PDF)]
15.	Current status of high performance quantum cascade lasers at the center for quantum devices M. Razeghi; A. Evans; Y. Bai; J. Nguyen; S. Slivken; S.R. Darvish; K. Mi Conference Proceedings - International Conference on Indium Phosphide and Related Materials. 588-593:[4266015] (2007)-- May 14, 2007 ...[Visit Journal] Mid-infrared laser sources are highly desired for laser-based trace chemical sensors, military countermeasures, free-space communications, as well as developing medical applications. While application development has been limited by the availability of adequate mid-infrared sources, InP-based quantum cascade lasers (QCLs) hold promise as inexpensive, miniature, portable solutions capable of producing high powers and operating at high temperatures with excellent beam quality and superior reliability. This paper discusses the most recent developments of application-ready high power (> 100 mW), continuous-wave (CW), mid-infrared QCLs operating above room temperature with lifetimes exceeding 13,000 hours. [reprint (PDF)]
15.	Long-term reliability of Al-free InGaAsP/GaAs λ = 808 nm) lasers at high-power high-temperature operation J. Diaz, H. Yi, M. Razeghi and G.T. Burnham Applied Physics Letters 71 (21)-- November 24, 1997 ...[Visit Journal] We report the long-term reliability measurement on uncoated Al-free InGaAsP/GaAs (λ = 808 nm) lasers at high-power and high-temperature operation. No degradation in laser performance has been observed for over 30 ,000 h of lifetime testing in any of randomly selected several 100 μm-wide uncoated lasers operated at 60 °C with 1 W continuous wave output power. This is the first and the most conclusive evidence ever reported that directly shows the high long-term reliability of uncoated Al-free lasers. [reprint (PDF)]
15.	Use of Sacrificial Zinc Oxide Template Layers for Epitaxial Lift-Off of Yttria-Stabilised Zirconia Thin Films D. J. Rogers, T. Maroutian, V. E. Sandana, P. Lecoeur, F. H. Teherani, P. Bove and M. Razeghi Proc. of SPIE 11687, 116872C (2021) ...[Visit Journal] 275 nm-thick Yttria-stabilised zirconia (YSZ) layers were grown on 240 nm-thick epitaxial (0002)-oriented ZnO buffer layers on c-sapphire substrates by pulsed laser deposition (PLD). X-ray diffraction (XRD) studies revealed high quality epitaxial growth with the YSZ having a preferential (111) orientation and a root mean square surface roughness of 1.4 nm over an area of 10 um x 10 um. The YSZ top surface was then temporary bonded to an Apiezon W wax carrier and the sample was immersed in 0.1M HCl so as to preferentially etch/dissolve away the ZnO underlayer and release of the YSZ from the sapphire substrate. XRD revealed only the characteristic (111) peak of YSZ after lift-off and thus confirmed both the dissolution of the ZnO and the preservation of the crystallographic integrity of the YSZ on the wax carrier. Optical and Atomic Force Microscopy revealed some buckling, roughening and cracking of the lifted YSZ, however, which was probably due to tensile epitaxial strain release. [reprint (PDF)]
15.	Ultraviolet Detectors for AstroPhysics Present and Future M. Ulmer, M. Razeghi, and E. Bigan Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 239-- February 6, 1995 ...[Visit Journal] Astronomical instruments for the study of UV astronomy have been developed for NASA missions such as the Hubble Space Telescope. The systems that are `blind to the visible' (`solar-blind') yet sensitive to the UV that have been flown in satellites have detective efficiencies of about 10 to 20%, although typically electron bombardment charge coupled devices are higher at 30 - 40% and ordinary CCDs achieve 1 - 5%. Therefore, there is a large payoff still to be gained by further improvements in the performance of solar blind UV detectors. We provide a brief review of some aspects of UV astronomy, UV detector development, and possible technologies for the future. We suggest that a particularly promising future technology is one based on the ability of investigators to produce high quality films made of wide bandgap III-V semiconductors. [reprint (PDF)]
15.	High Quality Type-II InAs/GaSb Superlattices with Cutoff Wavelength ~3.7 µm Using Interface Engineering Y. Wei, J. Bae, A. Gin, A. Hood, M. Razeghi, G.J. Brown, and M. Tidrow Journal of Applied Physics, 94 (7)-- October 1, 2003 ...[Visit Journal] We report the most recent advance in the area of Type-II InAs/GaSb superlattices that have cutoff wavelength of ~3.7 µm. With Ga_xIn_1–x type interface engineering techniques, the mismatch between the superlattices and the GaSb (001) substrate has been reduced to <0.1%. There is no evidence of dislocations using the best examination tools of x-ray, atomic force microscopy, and transmission electron microscopy. The full width half maximum of the photoluminescence peak at 11 K was ~4.5 meV using an Ar+ ion laser (514 nm) at fluent power of 140 mW. The integrated photoluminescence intensity was linearly dependent on the fluent laser power from 2.2 to 140 mW at 11 K. The temperature-dependent photoluminescence measurement revealed a characteristic temperature of one T1 = 245 K at sample temperatures below 160 K with fluent power of 70 mW, and T1 = 203 K for sample temperatures above 180 K with fluent power of 70 and 420 mW. [reprint (PDF)]
15.	Low frequency noise in 1024 x 1024 long wavelength infrared focal plane array base on Type-II InAs/GaSb superlattice A. Haddadi, S.R. Darvish, G. Chen, A.M. Hoang, B.M. Nguyen and M. Razeghi SPIE Proceedings, Vol. 8268, p. 82680X-- January 22, 2012 ...[Visit Journal] Recently, the type-II InAs/GaSb superlattice (T2SL) material platform is considered as a potential alternative for HgCdTe technology in long wavelength infrared (LWIR) imaging. This is due to the incredible growth in the understanding of its material properties and improvement of device processing which leads to design and fabrication of better devices. In this paper, we report electrical low frequency noise measurement on a high performance type-II InAs/GaSb superlattice 1024×1024 LWIR focal plane array. [reprint (PDF)]

Page 13 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (737 Items)