Center for Quantum Devices - Most Downloaded Journal Articles

Page 11 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)

13.	Novel process for direct bonding of GaN onto glass substrates using sacrificial ZnO template layers to chemically lift-off GaN from c-sapphire Rogers, D. J.; Ougazzaden, A.; Sandana, V. E.; Moudakir, T.; Ahaitouf, A.; Teherani, F. Hosseini; Gautier, S.; Goubert, L.; Davidson, I. A.; Prior, K. A.; McClintock, R. P.; Bove, P.; Drouhin, H.-J.; Razeghi, M. Proc. SPIE 8263, Oxide-based Materials and Devices III, 82630R (February 9, 2012)-- February 9, 2012 ...[Visit Journal] GaN was grown on ZnO-buffered c-sapphire (c-Al₂O₃) substrates by Metal Organic Vapor Phase Epitaxy. The ZnO then served as a sacrificial release layer, allowing chemical lift-off of the GaN from the c-Al₂O₃ substrate via selective wet etching of the ZnO. The GaN was subsequently direct-wafer-bonded onto a glass substrate. X-Ray Diffraction, Scanning Electron Microscopy, Energy Dispersive X-ray microanalysis, Room Temperature Photoluminescence & optical microscopy confirmed bonding of several mm2 of crack-free wurtzite GaN films onto a soda lime glass microscope slide with no obvious deterioration of the GaN morphology. Using such an approach, InGaN based devices can be lifted-off expensive single crystal substrates and bonded onto supports with a better cost-performance profile. Moreover, the approach offers the possibility of reclaiming and reusing the substrate. [reprint (PDF)]
13.	High performance mid-wavelength quantum dot infrared photodetectors for focal plane arrays M. Razeghi, H. Lim, S. Tsao, M. Taguchi, W. Zhang and A.A. Quivy SPIE Conference, San Diego, CA, Vol. 6297, pp. 62970C-- August 13, 2006 ...[Visit Journal] Quantum dot infrared photodetectors (QDIPs) have recently emerged as promising candidates for detection in the middle wavelength infrared (MWIR) and long wavelength infrared (LWIR) ranges. Here, we report our recent results for mid-wavelength QDIPs grown by low-pressure metalorganic chemical vapor deposition. Three monolayer of In_0.68Ga_0.32As self-assembled via the Stranski-Krastanov growth mode and formed lens-shaped InGaAs quantum dots with a density around 3×10₁₀ cm^-2. The peak responsivity at 77 K was measured to be 3.4 A/W at a bias of -1.9 V with 4.7 µm peak detection wavelength. Focal plane arrays (FPAs) based on these devices have been developed. The preliminary result of FPA imaging is presented. [reprint (PDF)]
13.	High-performance bias-selectable dual-band Short-/Mid-wavelength infrared photodetectors and focal plane arrays based on InAs/GaSb/AlSb Type-II superlattices M. Razeghi; A.M. Hoang; A. Haddadi; G. Chen; S. Ramezani-Darvish; P. Bijjam; P. Wijewarnasuriy; E. Decuir Proc. SPIE 8704, Infrared Technology and Applications XXXIX, 87041W (June 18, 2013)-- June 18, 2013 ...[Visit Journal] We report a bias selectable dual-band Type-II superlattice-based short-wave infrared (SWIR) and mid-wave infrared (MWIR) co-located photodetector capable of active and passive imaging. A new double-layer etch-stop scheme is introduced for back-side-illuminated photodetectors, which enhanced the external quantum efficiency both in the SWIR and MWIR spectral regions. Temperature-dependent dark current measurements of pixel-sized 27 μm detectors found the dark current density to be ∼1×10-5 A/cm2 for the ∼4.2 μm cut-off MWIR channel at 140 K. This corresponded to a reasonable imager noise equivalent difference in temperature of ∼49 mK using F/2.3 optics and a 10 ms integration time (tint), which lowered to ∼13 mK at 110 K using and integration time of 30 ms, illustrating the potential for high-temperature operation. The SWIR channel was found to be limited by readout noise below 150 K. An excellent imagery from the dual-band imager exemplifying pixel coincidence is shown. [reprint (PDF)]
13.	High-Power CW Mid-IR Quantum Cascade Lasers J.R. Meyer, W.W. Bewley, J.R. Lindle, I. Vurgaftman, A.J. Evans, J.S. Yu, S. Slivken, and M. Razeghi SPIE Conference, Jose, CA, -- January 22, 2005 ...[Visit Journal] We report the cw operation of quantum cascade lasers that do not require cryogenic cooling and emit at λ = 4.7-6.2 µm. At 200 K, more than 1 W of output power is obtained from 12-µm-wide stripes, with a wall-plug efficiency (η_wall) near 10%. Room-temperature cw operation has also been demonstrated, with a maximum output power of 640 mW (η_wall = 4.5%) at 6 µm and 260 mW (η_wall = 2.3%) at 4.8 µm. Far-field characterization indicates that whereas the beam quality remains close to the diffraction limit in all of the tested lasers, in the devices emitting at 6.2 µm the beam tends to steer by as much as 5-10° degrees in either direction with varying temperature and pump current. [reprint (PDF)]
13.	Monolithically, widely tunable quantum cascade lasers based on a heterogeneous active region design Wenjia Zhou, Neelanjan Bandyopadhyay, Donghai Wu, Ryan McClintock & Manijeh Razeghi Nature Scientific Reports 6, Article number: 25213 -- June 8, 2016 ...[Visit Journal] Quantum cascade lasers (QCLs) have become important laser sources for accessing the mid-infrared (mid-IR) spectral range, achieving watt-level continuous wave operation in a compact package at room temperature. However, up to now, wavelength tuning, which is desirable for most applications, has relied on external cavity feedback or exhibited a limited monolithic tuning range. Here we demonstrate a widely tunable QCL source over the 6.2 to 9.1 μm wavelength range with a single emitting aperture by integrating an eight-laser sampled grating distributed feedback laser array with an on-chip beam combiner. The laser gain medium is based on a five-core heterogeneous QCL wafer. A compact tunable laser system was built to drive the individual lasers within the array and produce any desired wavelength within the available spectral range. A rapid, broadband spectral measurement (520 cm⁻¹) of methane using the tunable laser source shows excellent agreement to a measurement made using a standard low-speed infrared spectrometer. This monolithic, widely tunable laser technology is compact, with no moving parts, and will open new opportunities for MIR spectroscopy and chemical sensing. [reprint (PDF)]
13.	Background limited performance of long wavelength infrared focal plane arrays fabricated from M-structure InAs-GaSb superlattices P.Y. Delaunay, B.M. Nguyen, D. Hoffman, E.K. Huang, and M. Razeghi IEEE Journal of Quantum Electronics, Vol. 45, No. 2, p. 157-162.-- February 1, 2009 ...[Visit Journal] The recent introduction of a M-structure design improved both the dark current and R₀A performances of Type-II InAs-GaSb photodiodes. A focal plane array fabricated with this design was characterized at 81 K. The dark current of individual pixels was measured between 1.1 and 1.6 nA, 7 times lower than previous superlattice FPAs. This led to a higher dynamic range and longer integration times. The quantum efficiency of detectors without antireflective coating was 74%. The noise equivalent temperature difference reached 23 mK, limited only by the performance of the testing system and the read out integrated circuit. Background limited performances were demonstrated at 81 K for a 300 K background. [reprint (PDF)]
13.	The effect of doping the M-barrier in very long-wave type-II InAs/GaSb heterodiodes D. Hoffman, B.M. Nguyen, E.K. Huang, P.Y. Delaunay, M. Razeghi, M.Z. Tidrow and J. Pellegrino Applied Physics Letters, Vol. 93, No. 3, p. 031107-1-- July 21, 2008 ...[Visit Journal] A variation on the standard homo-diode Type-II superlattice with an M-barrier between the pi-region and the n-region is shown to suppress the dark currents. By determining the optimal doping level of the M-superlattice, dark current densities of 4.95 mA·cm^-2 and quantum efficiencies in excess of 20% have been demonstrated at the moderate reverse bias of 50 mV; allowing for near background-limited performance with a Johnson-noise detectivity of 3.11×10¹⁰ Jones at 77 K for a 14.58 µm cutoff wavelength for large area diodes without passivation. This is comparable to values for the state-of-the-art HgCdTe photodiodes. [reprint (PDF)]
13.	320x256 Solar-Blind Focal Plane Arrays based on Al_xGa_1-xN R. McClintock, K. Mayes, A. Yasan, D. Shiell, P. Kung, and M. Razeghi Applied Physics Letters, 86 (1)-- January 3, 2005 ...[Visit Journal] We report AlGaN-based back-illuminated solar-blind ultraviolet focal plane arrays operating at a wavelength of 280 nm. The electrical characteristics of the individual pixels are discussed, and the uniformity of the array is presented. The p–i–n photodiode array was hybridized to a 320×256 read-out integrated circuit entirely within our university research lab, and a working 320×256 camera was demonstrated. Several example solar-blind images from the camera are also provided. [reprint (PDF)]
13.	Noise analysis in type-II InAs/GaSb focal plane arrays P.Y. Delaunay and M. Razeghi Journal of Applied Physics, Vol. 106, Issue 6, p. 063110-- September 15, 2009 ...[Visit Journal] A long wavelength infrared focal plane array based on type-II InAs/GaSb superlattices was fabricated and characterized at 80 K. The noise equivalent temperature difference in the array was measured as low as 23 mK for an integration time of 0.129 ms. The noise behavior of the detectors was properly described by a model based on thermal, shot, read out integrated circuit, and photon noises. The noise of the imager was dominated by photon noise for photon fluxes higher than 1.8×10¹⁵ ph·s⁻¹·cm⁻². At lower irradiance, the imager was limited by the shot noise generated by the dark current or the noise of the testing system. The superlattice detector did not create 1/f noise for frequencies above 4 mHz. As a result, the focal plane array did not require frequent calibrations. [reprint (PDF)]
13.	Recent advances in antimonide-based gap-engineered Type-II superlattices material system for 2 and 3 colors infrared imagers Manijeh. Razeghi, Abbas Haddadi, Arash Dehzangi, Romain Chevallier, and Thomas Yang Proceedings of SPIE 10177, Infrared Technology and Applications XLIII, 1017705-- May 9, 2017 ...[Visit Journal] InAs/InAs_1-xSb_x/AlAs_1-xSb_x type-II superlattices (T2SLs) is a system of multi-interacting quantum wells. Since its introduction, this material system has drawn a lot of attention especially for infrared detection. In recent years, InAs/InAs_1- xSb_x/AlAs_1-xSb_x T2SL material system has experienced incredible improvements in material quality, device structure designs and device fabrication process which elevated the performances of T2SL-based photodetectors to a comparable level to the state-of-the-art material systems for infrared detection such as Mercury Cadmium Telluride (MCT). In this paper, we will present the current status of InAs/InAs_1-xSb_x/AlAs_1-xSb_x T2SL-based photodetectors for detection in different infrared regions, from short-wavelength (SWIR) to long-wavelength (LWIR) infrared, and the future outlook of this material system. [reprint (PDF)]
13.	GaN avalanche photodiodes grown on m-plane freestanding GaN substrate Z. Vashaei, E. Cicek, C. Bayram, R. McClintock and M. Razeghi Applied Physics Letters, Vol. 96, No. 20, p. 201908-1-- May 17, 2010 ...[Visit Journal] M-plane GaN avalanche p-i-n photodiodes on low dislocation density freestanding m-plane GaN substrates were realized using metal-organic chemical vapor deposition. High quality homoepitaxial m-plane GaN layers were developed; the root-mean-square surface roughness was less than 1 Å and the full-width-at-half-maximum value of the x-ray rocking curve for (1010) diffraction of m-plane GaN epilayer was 32 arcsec. High quality material led to a low reverse-bias dark current of 8.11 pA for 225 μm² mesa photodetectors prior to avalanche breakdown, with the maximum multiplication gain reaching about 8000. [reprint (PDF)]
13.	AlGaN ultraviolet detectors M. Razeghi and A. Rogalski, SPIE Conference, San Jose, CA, -- February 12, 1997 ...[Visit Journal] Hitherto, the semiconductor ultraviolet (UV) detectors have been mainly fabricated using Si. Industries such as the aerospace, automotive, petroleum, and others have continuously provided the impetus pushing the development of fringe technologies which are tolerant of increasingly high temperatures and hostile environments. As a result, the main efforts are currently directed to anew generation of UV detectors fabricated from wide-band-gap semiconductors between them the most promising are diamond and AlGaN. The latest progress in development of AlGaN UV detectors is described in detail. [reprint (PDF)]
13.	Very high quality p-type Al_xGa_1-xN/GaN superlattice A. Yasan and M. Razeghi special ISDRS issue of Solid State Electronics Journal, 47-- January 1, 2003 ...[Visit Journal] Very high quality p-type Al_xGa_1−xN/GaN superlattice has been achieved through optimization of Mg flow and period of superlattice. Theoretical model was used to optimize the structure of superlattice by choosing suitable Al compositions and superlattice periods. The experiments show that for x=0.26, the resistivity is as low as 0.19 Ω cm and hole concentration is as high as 4.2×10¹⁸ cm⁻³, the highest values ever reported for p-type AlGaN/GaN superlattices. Hall effect measurement and admittance spectroscopy on the samples confirm the high quality of the superlattices. The activation energy calculated for p-type GaN and p-type A_0.1Ga_0.9N/GaN superlattice is estimated to be not, vert, similar 125 and 3 meV respectively. [reprint (PDF)]
13.	Optoelectronic Devices Based on III-V Compound Semiconductors Which Have Made a Major Scientific and Technological Impact in the Past 20 Years M. Razeghi IEEE Journal of Selected Topics in Quantum Electronics 6 (6), pp.1344 - 1354 -- November 1, 2000 ...[Visit Journal] This paper reviews some of our pioneering contributions to the field of III–V compound semiconductor materials and low-dimensional optoelectronic devices. These contributions span from the ultraviolet (200 nm) up to the far-infrared (25 μm) portion of the electromagnetic spectrum and have had a major scientific and technological impact on the semiconductor world in the past 20 years. [reprint (PDF)]
13.	Type-II ‘M’ Structure Photodiodes: An Alternative Material Design for Mid-Wave to Long Wavelength Infrared Regimes B-M. Nguyen, M. Razeghi, V. Nathan, and G.J. Brown SPIE Conference, January 25-29, 2007, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices IV, Vol. 6479, p. 64790S-1-10-- January 29, 2007 ...[Visit Journal] In this work, an AlSb-containing Type-II InAs/GaSb superlattice, the so-called M-structure, is presented as a candidate for mid and long wavelength infrared detection devices. The effect of inserting an AlSb barrier in the GaSb layer is discussed and predicts many promising properties relevant to practical use. A good agreement between the theoretical calculation based on Empirical Tight Binding Method framework and experimental results is observed, showing the feasibility of the structure and its properties. A band gap engineering method without material stress constraint is proposed. [reprint (PDF)]
13.	Pulsed metalorganic chemical vapor deposition of high quality AlN/GaN superlattices for intersubband transitions C. Bayram, B. Fain, N. Pere-Laperne, R. McClintock and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7222-12-- January 26, 2009 ...[Visit Journal] A pulsed metalorganic chemical vapor deposition (MOCVD) technique, specifically designed for high quality AlN/GaN superlattices (SLs) is introduced. Optical quality and precise controllability over layer thicknesses are investigated. Indium is shown to improve interface and surface quality. An AlN/GaN SL designed for intersubband transition at a telecommunication wavelength of ~1.5 µm, is grown, and processed for intersubband (ISB) absorption measurements. Room temperature measurements show intersubband absorption centered at 1.49 µm. Minimal (n-type) silicon doping of the well is shown to be crucial for good ISB absorption characteristics. The potential to extend this technology into the far infrared and even the terahertz (THz) region is also discussed. [reprint (PDF)]
13.	Type-II superlattice dual-band LWIR imager with M-barrier and Fabry-Perot resonance E.K. Huang, A. Haddadi, G. Chen, B.M. Nguyen, M.A. Hoang, R. McClintock, M. Stegall, and M. Razeghi OSA Optics Letters, Vol. 36, No. 13, p. 2560-2562-- July 1, 2011 ...[Visit Journal] We report a high performance long-wavelength IR dual-band imager based on type-II superlattices with 100% cutoff wavelengths at 9.5 μm (blue channel) and 13 μm (red channel). Test pixels reveal background-limited behavior with specific detectivities as high as ∼5×10¹¹ Jones at 7.9 μm in the blue channel and ∼1×10¹¹ Jones at 10.2 μm in the red channel at 77 K. These performances were attributed to low dark currents thanks to the M-barrier and Fabry–Perot enhanced quantum efficiencies despite using thin 2 μm absorbing regions. In the imager, the high signal-to-noise ratio contributed to median noise equivalent temperature differences of ∼20 mK for both channels with integration times on the order of 0.5 ms, making it suitable for high speed applications. [reprint (PDF)]
13.	Background limited long wavelength infrared type-II InAs/GaSb superlattice photodiodes operating at 110 K B.M. Nguyen, D. Hoffman, E.K. Huang, P.Y. Delaunay, and M. Razeghi Applied Physics Letters, Vol. 93, No. 12, p. 123502-1-- September 22, 2008 ...[Visit Journal] The utilization of the P+-pi-M-N+ photodiode architecture in conjunction with a thick active region can significantly improve long wavelength infrared Type-II InAs/GaSb superlattice photodiodes. By studying the effect of the depletion region placement on the quantum efficiency in a thick structure, we achieved a topside illuminated quantum efficiency of 50% for an N-on-P diode at 8.0 µm at 77 K. Both the double heterostructure design and the application of polyimide passivation greatly reduce the surface leakage, giving an R₀A of 416 Ω·cm² for a 1% cutoff wavelength of 10.52 µm, a Shot–Johnson detectivity of 8.1×10¹¹ cm·Hz^½/W at 77 K, and a background limited operating temperature of 110 K with 300 K background. [reprint (PDF)]
13.	Room temperature compact THz sources based on quantum cascade laser technology M. Razeghi; Q.Y. Lu; N. Bandyopadhyay; S. Slivken; Y. Bai Proc. SPIE 8846, Terahertz Emitters, Receivers, and Applications IV, 884602 (September 24, 2013)-- November 24, 2013 ...[Visit Journal] We present the high performance THz sources based on intracavity difference-frequency generation from mid-infrared quantum cascade lasers. Room temperature single-mode operation in a wide THz spectral range of 1-4.6 THz is demonstrated from our Čerenkov phase-matched THz sources with dual-period DFB gratings. High THz power up to 215 μW at 3.5 THz is demonstrated via epi-down mounting of our THz device. The rapid development renders this type of THz sources promising local oscillators for many astronomical and medical applications. [reprint (PDF)]
13.	Al_xGa_1-xN p-i-n Photodiodes on Sapphire Substrates D. Walker, P. Kung, P. Sandvik, J. Wu, M. Hamilton, I.H. Lee, J. Diaz, and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] We report the fabrication and characterization of Al_xGa1-xN p-i-n photodiodes (0.05 ≤ to X ≤ 0.30) grown on sapphire by low-pressure metalorganic chemical vapor deposition. The devices present a visible-rejection of about four orders of magnitude with a cutoff wavelength that shifts from 350 nm to 291 nm. They also exhibit a constant responsivity for five decades (30 mW/m² to 1 kW/m²) of optical power density. Using capacitance measurements, the values for the acceptor concentration in the p-Al_xGa_1-xN region and the unintentional donor concentration in the intrinsic region are found. Photocurrent decays are exponential for high load resistances, with a time constant that corresponds to the RC product of the system. For low load resistances the transient response becomes non-exponential, with a decay time longer than the RC constant. [reprint (PDF)]
13.	Broad area photonic crystal distributed feedback quantum cascade lasers emitting 34 W at λ ~ 4.36 μm B. Gokden, Y. Bai, N. Bandyopadhyay, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 97, No. 13, p. 131112-1-- September 27, 2010 ...[Visit Journal] We demonstrate room temperature, high power, single mode, and diffraction limited operation of a two dimensional photonic crystal distributed feedback quantum cascade laser emitting at 4.36 μm. Total peak power up to 34 W is observed from a 3 mm long laser with 400 μm cavity width at room temperature. Far-field profiles have M2 figure of merit as low as 2.5. This device represents a significant step toward realization of spatially and spectrally pure broad area high power quantum cascade lasers. [reprint (PDF)]
13.	The Molecular Beam Epitaxial Growth of InSb on (111) GaAs E. Michel, J. Kim, J. Xu, S. Javadpour, I. Ferguson, and M. Razeghi Applied Physics Letters 69 (2)-- July 8, 1996 ...[Visit Journal] The molecular beam epitaxial growth of InSb on (111)B GaAs has been investigated. It was found that for a given Sb/In ratio, a higher growth temperature was required for the growth of InSb on (111)B GaAs compared to that on (001) GaAs. This difference has been attributed to the bonding characteristics of the (111)B and (001) surface. Once growth had been optimized, it was found that the material characteristics of (111)B InSb were almost identical to that of (001) InSb, i.e., independent of orientation. For example, the x-ray full width at half-maximum and 300 K mobility had the same absolute values for (111) InSb and (001)InSb and followed the same dependence with the sample thickness. Te was found to be a well-behaved n-type dopant for (111)B InSb. [reprint (PDF)]
13.	Bias-selectable dual-band mid-/long-wavelength infrared photodetectors based on InAs/InAs_1−xSb_x type-II superlattices A. Haddadi, R. Chevallier, G. Chen, A. M. Hoang, and M. Razeghi Applied Physics Letters 106 , 011104-- January 8, 2015 ...[Visit Journal] A high performance bias-selectable mid-/long-wavelength infrared photodetector based on InAs/InAs_1−xSb_x type-II superlattices on GaSb substrate has been demonstrated. The mid- and long-wavelength channels' 50% cut-off wavelengths were ∼5.1 and ∼9.5 μm at 77 K. The mid-wavelength channel exhibited a quantum efficiency of 45% at 100 mV bias voltage under front-side illumination and without any anti-reflection coating. With a dark current density of 1 × 10⁻⁷ A/cm² under 100 mV applied bias, the mid-wavelength channel exhibited a specific detectivity of 8.2 × 10¹² cm·Hz^½·W^-1 at 77 K. The long-wavelength channel exhibited a quantum efficiency of 40%, a dark current density of 5.7 × 10⁻⁴ A/cm² under −150 mV applied bias at 77 K, providing a specific detectivity value of 1.64 × 10¹¹ cm·Hz^½·W^-1. [reprint (PDF)]
13.	Background–limited long wavelength infrared InAs/InAsSb type-II superlattice-based photodetectors operating at 110 K Abbas Haddadi, Arash Dehzangi, Sourav Adhikary, Romain Chevallier, and Manijeh Razeghi APL Materials 5, 035502 -- February 13, 2017 ...[Visit Journal] We report the demonstration of high-performance long-wavelength infrared (LWIR) nBn photodetectors based on InAs/InAsSb type-II superlattices. A new saw-tooth superlattice design was used to implement the electron barrier of the photodetectors. The device exhibited a cut-off wavelength of ∼10 μm at 77 K. The photodetector exhibited a peak responsivity of 2.65 A/W, corresponding to a quantum efficiency of 43%. With an R × A of 664 Ω·cm² and a dark current density of 8 × 10⁻⁵ A/cm², under −80 mV bias voltage at 77 K, the photodetector exhibited a specific detectivity of 4.72 × 10¹¹ Jones and a background–limited operating temperature of 110 K. [reprint (PDF)]
13.	Injector doping level dependent continuous-wave operation of InP-based QCLs at λ~ 7.3 µm above room temperature J.S. Yu, S. Slivken, and M. Razeghi Semiconductor Science and Technology (SST), Vol. 25, No. 12, p. 125015-- December 1, 2010 ...[Visit Journal] We report the continuous-wave (CW) operation of InGaAs/InAlAs quantum cascade lasers (QCLs) operating at λ ~ 7.3 µm above room temperature. The injector doping level–dependent CW characteristics above room temperature are investigated for doping densities between 7 × 10¹⁶ cm⁻³ and 2 × 10¹⁷ cm⁻³. The device performance, i.e. threshold current density, output power, operating temperature and characteristic temperature, depends strongly on the injector doping density. For a relatively low injector doping density of 7 × 10¹⁶ cm⁻³, a high-reflectivity-coated 10 µm wide and 4 mm long laser exhibits an improved device performance with an output power of 152 mW and a threshold current density of 1.37 kA cm⁻² at 298 K under CW mode, operating up to 343 K. The thermal characteristics are also analyzed by the estimation from the experimentally measured data for the QCLs with different injector doping densities. [reprint (PDF)]

Page 11 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)