Center for Quantum Devices - Most Downloaded Journal Articles

Page 10 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)

13.	Low-Threshold 7.3 μm Quantum Cascade Lasers Grown by Gas-Source Molecular Beam Epitaxy S. Slivken, A. Matlis, A. Rybaltowski, Z. Wu and M. Razeghi Applied Physics Letters 74 (19)-- May 19, 1999 ...[Visit Journal] We report low-threshold 7.3 μm superlattice-based quantum cascade lasers. The threshold current density is 3.4 kA/cm² at 300 K and 1.25 kA/cm² at 79 K in pulsed mode for narrow (∼20 μm), 2 mm-long laser diodes. The characteristic temperature (T₀) is 210 K. The slope efficiencies are 153 and 650 mW/A at 300 and 100 K, respectively. Power output is in excess of 100 mW at 300 K. Laser far-field intensity measurements give divergence angles of 64° and 29° in the growth direction and in the plane of the quantum wells, respectively. Far-field simulations show excellent agreement with the measured results. [reprint (PDF)]
13.	Emerging materials for photonics Miriam S. Vitiello, and Manijeh Razeghi APL Materials 5, 03510-- March 31, 2017 ...[Visit Journal] Photonics plays a major role in all aspects of human life. It revolutionized science by addressing fundamental scientiﬁc questions and by enabling key functions in many interdisciplinary ﬁelds spanning from quantum technologies to information andcommunicationscience,andfrombiomedicalresearchtoindustrialprocessmonitoring and life entertainment. [reprint (PDF)]
13.	Solar-Blind Al_xGa_1-xN p-i-n Photodetectors grown on LEO and non-LEO GaN P. Sandvik, D. Walker, P. Kung, K. Mi, F. Shahedipour, V. Kumar, X. Zhang, J. Diaz, C. Jelen, and M. Razeghi SPIE Conference, San Jose, CA, Vol. 3948, pp. 265 -- January 26, 2000 ...[Visit Journal] The III-Nitride material system is an excellent candidate for UV photodetector applications due to its wide, direct bandgaps and robust material nature. However, despite many inherent material advantages, the III-Nitride material system typically suffers from a large number of extended defects which degrade material quality and device performance. One technique aimed at reducing defect densities in these materials is lateral epitaxial overgrowth (LEO). In this work, we present a preliminary comparison between AlGaN UV, solar-blind p-i-n photodiodes fabricated form LEO GaN and non-LEO GaN. Improvements in both responsivity and rejection ratio are observed, however, further device improvements are necessary. For these, we focus on the optimization of the p- i-n structure and a reduction in contact resistivity to p- GaN and p-AlGaN layers. By improving the structure of the device, GaN p-i-n photodiodes were fabricated and demonstrate 86 percent internal quantum efficiency at 362 nm and a peak to visible rejection ratio of 105. Contact treatments have reduced the contact resistivity to p-GaN and p-AlGaN by over one order of magnitude form our previous results. [reprint (PDF)]
13.	Self-assembled semiconductor quantum dot infrared photodetector operating at room temperature and focal plane array Ho-Chul Lim; Stanley Tsao; Wei Zhang; Manijen Razeghi Proc. SPIE 6542, Infrared Technology and Applications XXXIII, 65420R (May 14, 2007)-- May 14, 2007 ...[Visit Journal] Self-assembled semiconductor quantum dots have attracted much attention because of their novel properties and thus possible practical applications including the lasers, detectors and modulators. Especially the photodetectors which have quantum dots in their active region have been developed and show promising performances such as high operation temperature due to three dimensional confinement of the carriers and normal incidence in contrast to the case of quantum well detectors which require special optical coupling schemes. Here we report our recent results for mid-wavelength infrared quantum dot infrared photodetector grown by low-pressure metalorganic chemical vapor deposition. The material system we have investigated consists of 25 period self-assembled InAs quantum dot layers on InAlAs barriers, which are lattice-matched to InP substrates, covered with InGaAs quantum well layers and InAlAs barriers. This active region was sandwiched by highly doped InP contact layers. The device operates at 4.1 μm with a peak detectivity of 2.8×10¹¹ cm·Hz^1/2/W at 120 K and a quantum efficiency of 35 %. The photoresponse can be observed even at room temperature resulting in a peak detectivity of 6×10⁷ cm·Hz^1/2/W. A 320×256 focal plane array has been fabricated in this kind of device. Its performance will also be discussed here. [reprint (PDF)]
13.	Transport properties in n-type InSb films grown by metalorganic chemical vapor deposition S.N. Song, J.B. Ketterson, Y.H. Choi, R. Sudharsanan, and M. Razeghi Applied Physics Letters 63 (7)-- August 16, 1993 ...[Visit Journal] We have measured the temperature and magnetic field dependence of the Hall mobility and transverse magnetoresistance in n-type InSb films epitaxially grown on GaAs substrates by metalorganic chemical vapor deposition. The films show a giant magnetoresistance: e.g., at 240 K the resistivity increases over 20 times at a magnetic field of 5 T; the low field coefficient of resistivity at 77 K is as high as 47.5 μ·Ω· cm/G. The Hall mobility decreases with magnetic field and saturates at higher fields. By taking the interface carrier transport into account, the observed field dependence of the Hall mobility and magnetoresistance may be understood based on a two-layer model. [reprint (PDF)]
13.	Very high wall plug efficiency of quantum cascade lasers Y. Bai, S. Slivken, S.R. Darvish, and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7608, p. 76080F-1-- January 22, 2010 ...[Visit Journal] We demonstrate very high wall plug efficiency (WPE) of mid-infrared quantum cascade lasers (QCLs) in low temperature pulsed mode operation (53%), room temperature pulsed mode operation (23%), and room temperature continuous wave operation (18%). All of these values are the highest to date for any QCLs. The optimization of WPE takes the route of understanding the limiting factors of each sub-efficiency, exploring new designs to overcome the limiting factor, and constantly improving the material quality. [reprint (PDF)]
13.	Techniques for High-Quality SiO₂ Films J. Nguyen and M. Razeghi SPIE Conference, January 25-29, 2007, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices IV, Vol. 6479, p. 64791K-1-8-- January 29, 2007 ...[Visit Journal] We report on the comparison of optical, structural, and electrical properties of SiO₂ using plasma-enhanced chemical vapor deposition and ion-beam sputtering deposition. High-quality, low-temperature deposition of SiO₂ by ion-beam sputtering deposition is shown to have lower absorption, smoother and more densely packed films, a lower amount of fixed oxide charges, and a lower trapped-interface density than SiO₂ by plasma-enhanced chemical vapor deposition. This high-quality SiO₂ is then demonstrated as an excellent electrical and mechanical surface passivation layer on Type-II InAs/GaSb photodetectors [reprint (PDF)]
13.	Cubic Phase GaN on Nano-grooved Si (100) via Maskless Selective Area Epitaxy Bayram, C., Ott, J. A., Shiu, K.-T., Cheng, C.-W., Zhu, Y., Kim, J., Razeghi, M. and Sadana, D. K. Adv. Funct. Mater. 2014-- April 1, 2014 ...[Visit Journal] A method of forming cubic phase (zinc blende) GaN (referred as c-GaN) on a CMOS-compatible on-axis Si (100) substrate is reported. Conventional GaN materials are hexagonal phase (wurtzite) (referred as h-GaN) and possess very high polarization fields (∼MV/cm) along the common growth direction of <0001>. Such large polarization fields lead to undesired shifts (e.g., wavelength and current) in the performance of photonic and vertical transport electronic devices. The cubic phase of GaN materials is polarization-free along the common growth direction of <001>, however, this phase is thermodynamically unstable, requiring low-temperature deposition conditions and unconventional substrates (e.g., GaAs). Here, novel nano-groove patterning and maskless selective area epitaxy processes are employed to integrate thermodynamically stable, stress-free, and low-defectivity c-GaN on CMOS-compatible on-axis Si. These results suggest that epitaxial growth conditions and nano-groove pattern parameters are critical to obtain such high quality c-GaN. InGaN/GaN multi-quantum-well structures grown on c-GaN/Si (100) show strong room temperature luminescence in the visible spectrum, promising visible emitter applications for this technology. [reprint (PDF)]
13.	Stranski-Krastanov growth of InGaN quantum dots emitting in green spectra C. Bayram and M. Razeghi Applied Physics A: Materials Science and Processing, Vol. 96, No. 2, p. 403-408-- August 1, 2009 ...[Visit Journal] Self-assembled InGaN quantum dots (QDs) were grown on GaN templates by metalorganic chemical vapor deposition. 2D–3D growth mode transition through Stranski–Krastanov mode was observed via atomic force microscopy. The critical thickness for In_0.67Ga_0.33N QDs was determined to be four monolayers. The effects of growth temperature, deposition thickness, and V/III ratio on QD formation were examined. The capping of InGaN QDs with GaN was analyzed. Optimized InGaN quantum dots emitted in green spectra at room temperature. [reprint (PDF)]
13.	High power quantum cascade lasers M. Razeghi, S. Slivken, Y. Bai, B. Gokden, and S.R. Darvish New Journal of Physics (NJP), Volume 11, p. 125017-- December 1, 2009 ...[Visit Journal] We report the most recent state-of-art quantum cascade laser results at wavelengths around 4.8 and 10 μm. At 4.8 μm, a room temperature wall plug efficiency (WPE) of 22 and 15.5% are obtained in pulsed mode and continuous wave (cw) mode, respectively. Room temperature cw output power reaches 3.4 W. The same laser design is able to reach a WPE of 36% at 120 K in pulsed mode. At 10 μm, room temperature average power of 2.2 W and cw power of 0.62 W are obtained. We also explore lasers utilizing the photonic crystal distributed feedback mechanism, and we demonstrate up to 12 W peak power operation at three different wavelengths around 4.7 μm with a waveguide width of 100 μm and diffraction limited beam quality. [reprint (PDF)]
13.	Low-threshold and high power (~9.0 μm) quantum cascade lasers operating at room temperature A. Matlis, S. Slivken, A. Tahraoui, K.J. Luo, J. Diaz, Z. Wu, A. Rybaltowski, C. Jelen, and M. Razeghi Applied Physics Letters 77 (12)-- September 18, 2000 ...[Visit Journal] We report a low threshold current density and high power for λ ∼ 9 μm AlInAs/GaInAs quantum cascade lasers operating at room temperature. The threshold current density is 1.95 kA/cm² at 300 K and 0.61 kA/cm² at 80 K for 5 μs pulses at 200 Hz repetition rate. The peak output power is 700 mW at room temperature and 1.3 W at 80 K per two facets for cavity length is 3 mm with a stripe width of 20 μm. The characteristic temperature T₀ is 185 °C. The slope efficiency is 450 and 800 mW/A at 300 and 80 K, respectively. In continuous wave operation, the output power is more than 150 mW at 80 K and 25 mW at 140 K. This high performance was achieved by improving the material growth and processing technology. [reprint (PDF)]
13.	High-detectivity quantum-dot infrared photodetectors grown by metal-organic chemical-vapor deposition J. Szafraniec, S. Tsao, W. Zhang, H. Lim, M. Taguchi, A.A. Quivy, B. Movaghar and M. Razeghi Applied Physics Letters 88 (121102)-- March 20, 2006 ...[Visit Journal] A mid-wavelength infrared photodetector based on InGaAs quantum dots buried in an InGaP matrix and deposited on a GaAs substrate was demonstrated. Its photoresponse at T=77 K was measured to be around 4.7 μm with a cutoff at 5.5 μm. Due to the high peak responsivity of 1.2 A/W and low dark-current noise of the device, a specific peak detectivity of 1.1 x 10¹² cm·Hz^½·W⁻¹ was achieved at −0.9 V bias [reprint (PDF)]
13.	ZnO Thin Film Templates for GaN-based Devices D.J. Rogers, F. Hosseini Teherani, A. Yasan, R. McClintock, K. Mayes, S.R. Darvish, P. Kung, M. Razeghi and G. Garry SPIE Conference, Jose, CA, Vol. 5732, pp. 412-- January 22, 2005 ...[Visit Journal] GaN-based optoelectronic devices are plagued by a tendency to non-radiative transitions linked to defects in the active layers. ZnO is promising as a substrate material for GaN because it has the same wurtzite structure and a relatively small lattice mismatch (~1.8%). In this paper, we discuss use of ZnO thin films as templates for GaN based LED. [reprint (PDF)]
13.	High peak power 16 m InP-related quantum cascade laser A. Szerlinga,∗, S. Slivkenb, M. RazeghibaInstytut Opto-Electronics Review 25, pp. 205–208-- July 22, 2017 ...[Visit Journal] tIn this paper ∼16 μm-emitting multimode InP-related quantum cascade lasers are presented with themaximum operating temperature 373 K, peak and average optical power equal to 720 mW and 4.8 mW at 303 K, respectively, and the characteristic temperature (T₀) 272 K. Two types of the lasers were fabricatedand characterized: the lasers with a SiO₂ layer left untouched in the area of the metal-free window ontop of the ridge, and the lasers with the SiO₂layer removed from the metal-free window area. Dual-wavelength operation was obtained, at ∼15.6 μm (641 cm⁻¹) and at ∼16.6 μm (602 cm⁻¹) for laserswith SiO₂-removed, while within the emission spectrum of the lasers with SiO₂-left untouched only the former lasing peak was present. The parameters of these devices like threshold current, optical power and emission wavelength are compared. Lasers without the SiO₂ layer showed ∼15% lower threshold current than these ones with the SiO₂ layer. The optical powers for lasers without SiO₂ layer were almost twice higher than for the lasers with the SiO₂ layer on the top of the ridge. [reprint (PDF)]
13.	High performance quantum dot-quantum well infrared focal plane arrays S. Tsao, A. Myzaferi, and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7605, p. 76050J-1-- January 27, 2010 ...[Visit Journal] Quantum dot (QD) devices are a promising technology for high operating temperature detectors. We have studied InAs QDs embedded in an InGaAs/InAlAs quantum well structure on InP substrate for middle wavelength infrared detectors and focal plane arrays (FPAs). This combined dot-well structure has weak dot confinement of carriers, and as a result, the device behavior differs significantly from that in more common dot systems with stronger confinement. We report on our studies of the energy levels in the QDWIP devices and on QD-based detectors operating at high temperature with D* over 10¹⁰ cm·Hz^½/W at 150 K operating temperature and high quantum efficiency over 50%. FPAs have been demonstrated operating at up to 200 K. We also studied two methods of adapting the QDWIP device to better accommodate FPA readout circuit limitations. [reprint (PDF)]
13.	High Power Mid-Infrared Quantum Cascade Lasers Grown on Si Steven Slivken, Nirajman Shrestha, and Manijeh Razeghi Photonics, vol. 9, 626 ...[Visit Journal] This article details the demonstration of a strain-balanced, InP-based mid-infrared quantum cascade laser structure that is grown directly on a Si substrate. This is facilitated by the creation of a metamorphic buffer layer that is used to convert from the lattice constant of Si (0.543 nm) to that of InP (0.587 nm). The laser geometry utilizes two top contacts in order to be compatible with future large-scale integration. Unlike previous reports, this device is capable of room temperature operation with up to 1.6 W of peak power. The emission wavelength at 293 K is 4.82 um, and the device operates in the fundamental transverse mode. [reprint (PDF)]
13.	Recent Advances in Room Temperature, High-Power Terahertz Quantum Cascade Laser Sources Based on Difference-Frequency Generation Quanyong Lu and Manijeh Razeghi Photonics, 3, 42-- July 7, 2016 ...[Visit Journal] We present the current status of high-performance, compact, THz sources based on intracavity nonlinear frequency generation in mid-infrared quantum cascade lasers. Significant performance improvements of our THz sources in the power and wall plug efficiency are achieved by systematic optimizing the device’s active region, waveguide, and chip bonding strategy. High THz power up to 1.9 mW and 0.014 mW for pulsed mode and continuous wave operations at room temperature are demonstrated, respectively. Even higher power and efficiency are envisioned based on enhancements in outcoupling efficiency and mid-IR performance. Our compact THz device with high power and wide tuning range is highly suitable for imaging, sensing, spectroscopy, medical diagnosis, and many other applications. [reprint (PDF)]
13.	Widely tuned room temperature terahertz quantum cascade laser sources based on difference-frequency generation Q.Y. Lu, N. Bandyopadhyay, S. Slivken, Y. Bai and M. Razeghi Applied Physics Letters, Vol. 101, No. 25, p. 251121-1-- December 17, 2012 ...[Visit Journal] We demonstrate room temperature THz quantum cascade laser sources with a broad spectral coverage based on intracavity difference-frequency generation. Two mid-infrared active cores based on the single-phonon resonance scheme are designed with a THz nonlinearity specially optimized at the high operating fields that correspond to the highest mid-infrared output powers. A Čerenkov phase-matching scheme along with integrated dual-period distributed feedback gratings are used for efficient THz extraction and spectral purification. Single mode emissions from 1.0 to 4.6 THz with a side-mode suppression ratio and output power up to 40 dB and 32 μW are obtained, respectively. [reprint (PDF)]
13.	New design strategies for multifunctional and inexpensive quantum cascade lasers Steven Slivken; Manijeh Razeghi Proc. SPIE 10926, Quantum Sensing and Nano Electronics and Photonics XVI, 1092611-- February 1, 2019 ...[Visit Journal] This manuscript describes some of the new advances in active mid-infrared photonic integrated circuits enabled by new quantum cascade laser technologies. This includes monolithic beam steering which was achieved via the integration of a widely tunable QCL and a tapered grating outcoupler. A record 17.9 degrees of steering with a low divergence beam (0.5 degrees) was achieved. In addition, the use of surface emitting architectures is proposed as a means to reduce the manufacturing cost of next-generation QCLs. A reflective outcoupler is demonstrated which can allow for stable surface emission from a quantum cascade laser and has potential for cost-effective wafer-scale manufacturing. This outcoupler is integrated with an amplified, electrically tunable laser architecture to demonstrate high power surface emission at a wavelength near 4.9 μm. Single mode peak power up to 6.7 W is demonstrated with >6 W available over a 90 cm⁻¹ (215 nm) spectral range. All of this is achieved while maintaining a high quality output beam, similar to a standard edge emitter. [reprint (PDF)]
13.	Comparison of ZnO nanostructures grown using pulsed laser deposition, metal organic chemical vapor deposition, and physical vapor transport V.E. Sandana, D.J. Rogers, F. Hosseini Teherani, R. McClintock, C. Bayram, M. Razeghi, H-J Drouhin, M.C. Clochard, V. Sallett, G. Garry, and F. Falyouni Journal of Vacuum Science and Technology B, Vol. 27, No. 3, May/June, p. 1678-1683-- May 29, 2009 ...[Visit Journal] This article compares the forms and properties of ZnO nanostructures grown on Si (111) and c-plane sapphire (c-Al₂O₃) substrates using three different growth processes: metal organic chemical vapor deposition (MOCVD), pulsed laser deposition (PLD), and physical vapor transport (PVT). A very wide range of ZnO nanostructures was observed, including nanorods, nanoneedles, nanocombs, and some novel structures resembelling “bevelled” nanowires. PVT gave the widest family of nanostructures. PLD gave dense regular arrays of nanorods with a preferred orientation perpendicular to the substrate plane on both Si and c-Al₂O₃ substrates, without the use of a catalyst. X-ray diffraction (XRD) studies confirmed that nanostructures grown by PLD were better crystallized and more highly oriented than those grown by PVT and MOCVD. Samples grown on Si showed relatively poor XRD response but lower wavelength emission and narrower linewidths in PL studies. [reprint (PDF)]
13.	Multi-color 4–20 μm In-P-based Quantum Well Infrared Photodetectors C. Jelen, S. Slivken, G.J. Brown, and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] In order to tune the wavelength of lattice-matched QWIP detectors over the range from 4 - 20 &mum, new designs are demonstrated for the first time which combine InGaAlAs and InGaAsP layers lattice-matched to InP and grown by gas-source molecular beam epitaxy. We demonstrate the first long-wavelength quantum well infrared photodetectors using the lattice-matched n-doped InGaAlAs/InP materials system. Samples with AlAs mole fractions of 0.0, 0.1, and 0.15 result in cutoff wavelengths of 8.5, 13.3, and 19.4 μm, respectively. A 45 degree facet coupled illumination responsivity of R equals 0.37 A/W and detectivity of D*(λ) equals 1x10⁹ cm·Hz^½·W^-1 at T = 77 K, for a cutoff wavelength λ_c equals 13.3 μm have been achieved. Based on the measured intersubband photoresponse wavelength, a null conduction band offset is expected for In_0.52Ga_0.21Al_0.27As/InP heterojunctions. We also report quantum well infrared photodetector structures of In_0.53Ga_0.47As/Al_0.48In_0.52As grown on InP substrate with photoresponse at 4 μm suitable for mid-wavelength infrared detectors. These detectors exhibit a constant peak responsivity of 30 mA/W independent of temperature in the range from T equals 77 K to T equals 200 K. Combining these two materials, we report the first multispectral detectors that combine lattice-matched quantum wells of InGaAs/InAlAs and InGaAs/InP. Utilizing two contacts, a voltage tunable detector with (lambda) p equals 8 micrometer at a bias of V equals 5 V and λ_p equals 4 μm at V equals 10 V is demonstrated. [reprint (PDF)]
13.	Investigation of Enhanced Heteroepitaxy and Electrical Properties in k-Ga2O3 due to Interfacing with β-Ga2O3 Template Layers Junhee Lee, Lakshay Gautam, Ferechteh H. Teherani, Eric V. Sandana, P. Bove, David J. Rogers and Manijeh Razeghi J. Lee, M. Razeghi, Physica Status Solidi A 2023,220, 2200559, https://doi.org/10.1002/pssa.202200559 ...[Visit Journal] Heteroepitaxial k-Ga2O3 films grown by metal-organic chemical vapor deposition (MOCVD) were found to have superior materials and electrical properties thanks to the interfacing with a b-Ga2O3 template layer. k-Ga2O3grown on sapphire has not been able to demonstrate its full potential due to materials imperfections created by strain induced by the lattice mismatch at the interface between the epilayer and the substrate. By adopting a b-Ga2O3 template on a c-sapphire substrate, higher quality k-Ga2O3thin films were obtained, as evidenced by a smoother surface morphology, narrower XRD peaks, and superior electrical performance. The implications of this phenomenon, caused by b-Ga2O3 buffer layer, are already very encouraging for both boosting current device performance and opening up the perspective of novel applications for Ga2O3. [reprint (PDF)]
13.	Mid-wavelength infrared heterojunction phototransistors based on type-II InAs/AlSb/GaSb superlattices A. Haddadi, S. Adhikary, A. Dehzangi, and M. Razeghi Applied Physics Letters 109, 021107-- July 12, 2016 ...[Visit Journal] A mid-wavelength infrared heterojunction phototransistor based on type-II InAs/AlSb/GaSb superlattices on GaSb substrate has been demonstrated. Near a wavelength of 4 μm saturated optical gains of 668 and 639 at 77 and 150 K, respectively, are demonstrated over a wide dynamic range. At 150 K, the unity optical gain collector dark current density and DC current gain are 1 × 10⁻³ A/cm² and 3710, respectively. This demonstrates the potential for use in high-speed applications. In addition, the phototransistor exhibits a specific detectivity value that is four times higher compared with a state-of-the-art type-II superlattice-based photodiode with a similar cut-off wavelength at 150 K. [reprint (PDF)]
13.	Comprehensive study of blue and green multi-quantum-well light-emitting diodes grown on conventional and lateral epitaxial overgrowth GaN C. Bayram, J.L. Pau, R. McClintock and M. Razeghi Applied Physics B: Lasers and Optics, Vol. 95, p. 307-314-- November 29, 2008 ...[Visit Journal] Growths of blue and green multi-quantum wells (MQWs) and light-emitting diodes (LEDs) are realized on lateral epitaxial overgrowth (LEO) GaN, and compared with identical structures grown on conventional GaN. Atomic force microscopy is used to confirm the significant reduction of dislocations in the wing region of our LEO samples before active-region growth. Differences between surface morphologies of blue and green MQWs are analyzed. These MQWs are integrated into LEDs. All devices show a blue shift in the electroluminescence (EL) peak and narrowing in EL spectra with increasing injection current, both characteristics attributed to the band-gap renormalization. Green LEDs show a larger EL peak shift and a broader EL spectrum due to larger piezoelectric field and more indium segregation in the MQWs, respectively. Blue LEDs on LEO GaN show a higher performance than those on conventional GaN; however, no performance difference is observed for green LEDs on LEO GaN versus conventional GaN. The performance of the green LEDs is shown to be primarily limited by the active layer growth quality. [reprint (PDF)]
13.	High Detectivity GaInAs/InP Quantum Well Infrared Photodetectors Grown on Si Substrates J. Jiang, C. Jelen, M. Razeghi and G.J. Brown IEEE Photonics Technology Letters 14 (3)-- March 1, 2002 ...[Visit Journal] In this letter, we report an improvement in the growth and the device performance of GaInAs-InP quantum well infrared photodetectors grown on Si substrates. Material growth techniques, like low-temperature nucleation layers and thick buffer layers were used to grow InP on Si. An in situ thermal cycle annealing technique was used to reduce the threading dislocation density in the InP-on-Si. Detector dark current was reduced 2 orders of magnitude by this method. Record high detectivity of 2.3 × 10⁹ cm·Hz^½·W^-1 was obtained for QWIP-on-Si detectors in the 7-9 μm range at 77 K [reprint (PDF)]

Page 10 of 30: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 >> Next (732 Items)